manualshive.com logo in svg

EXFO Power Blazer 88000 Series, Руководство пользователя

Экспертный тестер сетей EXFO Power Blazer 88000 Series - надежное устройство для тестирования и мониторинга сетей. Для ознакомления с возможностями и настройками прибора скачайте бесплатное руководство пользователя на manualshive.com. Узнайте как максимально эффективно использовать этот инструмент для анализа сетевых проблем.

Поделиться
Скачать
background image

Test Setup - Test Configurator, Timer, and System

Power Blazer

211

MAC/IP/UDP

Note:

Source/Destination Flooding

 and 

Flood Range

 are only available with 

Traffic Gen & Mon when the Network Layer is set to None (see page 206).

 

Source Flooding

 and 

Destination Flooding

 check boxes when 

selected (cleared by default) allows generation of frames using 
source/destination MAC addresses flooding as follows: The first frame 
is transmitted starting with the least significant bits of the 
source/destination MAC address covered by the range set to 0; each 
subsequent frame is transmitted by incrementing the least significant 
bits by 1; when the upper limit of the range is reached, the 
source/destination MAC address restarts over with the least significant 
bits covered by the range set to 0. 

Flood Range

 is the range of the least significant bits used for the 

Source Flooding and/or Destination Flooding: 

2 (1 bit)

, 

4 (2 bits)

, 

8 (3 bits)

, 

16 (4 bits)

... up to 

16777216 (24 bits)

 (default). 

VLAN

Note:

VLAN is only available when the VLAN Tag is enabled; refer to 

Modify 

Frame Structure

 on page 205. 

For each VLAN tag enabled (C-VLAN/S-VLAN/E-VLAN) the following 
parameters are configurable.

VLAN ID

 choices are 

0

 through 

4095

; refer to 

VLAN ID and Priority

 on 

page 758 for more information. 

Priority

, VLAN user priority, choices are 

0

 (default) to 

7

. Refer to 

VLAN 

ID and Priority

 on page 758 for more information. 

Type

, VLAN Ethernet Type, choices are 

8100

 (default for C-VLAN), 

88A8

 (default for S-VLAN), 

9100

 (default for E-VLAN), 

9200

, and 

9300

.

Drop Eligible

:, when set to 

Yes

 (DEI = 1), the transmitted frames will 

be dropped first on receipt when congestion occurs under test. Drop 
Eligible is not available when VLAN type is 8100. This parameter is set 
to 

No

 by default. 

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

ABB HF Series Manual preview
HF Series
Бренд: ABB Страницы: 63
UNITED 7700 Series Maintenance & Operation Manual preview
7700 Series
Бренд: UNITED Страницы: 8
B&R Industries AP1000 User Manual preview
AP1000
Бренд: B&R Industries Страницы: 89
IFM CR710S Original Operating Instructions preview
CR710S
Бренд: IFM Страницы: 49
Purmo NC 24 V Assembly Instructions preview
NC 24 V
Бренд: Purmo Страницы: 2
salmson ACSON VARIO Installation And Starting Instructions preview
ACSON VARIO
Бренд: salmson Страницы: 78
D+H DXD 150-BSY+ Original Instructions Manual preview
DXD 150-BSY+
Бренд: D+H Страницы: 16
Xylem Bell & Gossett Technologic PPS Quick Start Manual preview
Bell & Gossett Technologic PPS
Бренд: Xylem Страницы: 20
Toro 53381 Installation Instructions preview
53381
Бренд: Toro Страницы: 2
IR-Tec OS-NET Programming Manual preview
OS-NET
Бренд: IR-Tec Страницы: 14
Jeckson Electric 47-1010A-T Owner'S Manual preview
47-1010A-T
Бренд: Jeckson Electric Страницы: 2
Blue Point Engineering DMX Analyzer Manual preview
DMX Analyzer
Бренд: Blue Point Engineering Страницы: 12
Conbraco Industries Apollo 70-600 Series Installation, Operation And Maintenance Manual preview
Apollo 70-600 Series
Бренд: Conbraco Industries Страницы: 4
Ravel RE - 104 Installation, Commissioning & Operating Manual preview
RE - 104
Бренд: Ravel Страницы: 33
ICP DAS USA WISE-5801 Application Example preview
WISE-5801
Бренд: ICP DAS USA Страницы: 20
iNels JA3-018M Quick Start Manual preview
JA3-018M
Бренд: iNels Страницы: 2
GTO SW-4000XL Installation Manual preview
SW-4000XL
Бренд: GTO Страницы: 44
KORINS EPIP-40 /30A(I) Instruction Manual preview
EPIP-40 /30A(I)
Бренд: KORINS Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды