EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 218 / 803

background image

Test Setup - Test Configurator, Timer, and System

206

88000 Series

MAC/IP/UDP



Framing

Note:

The framing for EtherSAM in a NAT environment is limited to Ethernet II,
IPv4, and UDP.



Frame Format

(layer 2) allows selecting

Ethernet II

(default) or

802.3 SNAP

as the frame format.



Network Layer

1

(layer 3) sets the network traffic type:

IPv4

(default)/

IPv6

, or

None

.



Transport Layer

is disabled when the

Network Layer

is

None

.



MPLS

: The

MPLS Label

check box, when selected (cleared by

default), enables 1 or 2 MPLS labels allowing management and test
frames to be transmitted and received. Only available with EtherSAM
and Traffic Gen & Mon test applications. Not available when using

Provider Encapsulation

.

Not available with EtherSAM when the

S-OAM check box is selected.



VLAN

: The

VLAN Tag

check box when selected (cleared by default),

enables up to 3 stacked VLAN; up to 2 staked VLAN when using

Provider Encapsulation

.

1. Not available with EtherSAM when the

S-OAM

check box selected. Not available when using Provider Encapsulation.

Not configurable and set to None for 40GE and 100GE dual port topology and 400GE test.

Test Application

Transport Layer

EtherSAM

None

,

UDP

(default),

TCP

a

a.

Only available for 10M to 10G.

RFC 2544

UDP

EtherBERT

UDP

(default),

TCP

Traffic Gen & Mon

None, UDP

(default),

«
...
216
217
218
219
220
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 26

Бренд: NAiS Страницы: 199

Бренд: Panasonic Страницы: 38

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 179

Бренд: Panasonic Страницы: 23

Бренд: Panasonic Страницы: 30

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 44

Бренд: Panasonic Страницы: 20

INDUSTRY PAN9028

Бренд: Panasonic Страницы: 34

Бренд: Magnescale Страницы: 132

medialon Showmaster Go

Бренд: 7th Sense Страницы: 2

Бренд: Danfoss Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды