E X C E L D R Y E R , I N C 1 . 8 0 0 . 2 5 5 . 9 2 3 5 E X C E L D R Y E R . C O M A D M I N @ E X C E L D R Y E R . C O M
3 5 7 C H E S T N U T S T R E E T, E A S T L O N G M E A D O W , M A 0 1 0 2 8
0 2 / 2 0 1 6
3
R E A D A N D S AV E T H E S E I N S T R U C T I O N S
W ARNING : TO REDUCE THE RISK OF F IRE, EL ECTRIC SHOCK OR INJ URY TO P ERSONS,
OB SERVE THE F OL L OW ING :
A. Us e t h i s u n i t o n l y i n t h e m a n n e r i n t e n d e d b y t h e m a n u f a c t u r e r .
B . B e f o r e s e r v i c i n g o r c l e a n i n g u n i t , s w i t c h p o w e r o f f a t s e r v i c e p a n e l a n d l o c k t h e s e r v i c e
d i s c o n n e c t i n g m e a n s t o p r e v e n t p o w e r f r o m b e i n g s w i t c h e d o n a c c i d e n t a l l y . W h e n t h e
s e r v i c e d i s c o n n e c t i n g m e a n s c a n n o t b e l o c k e d , s e c u r e l y f a s t e n a p r o m i n e n t w a r n i n g d e v i c e ,
s u c h a s a t a g , t o t h e s e r v i c e p a n e l .
CL EANING / M AINTENANCE
OUTSIDE
Gently wash Cover (including air inlet holes) using a soft cloth or sponge and a mild soap or detergent with
lukewarm water to loosen dirt and grime.
INSIDE
Excel recommends inspecting the inside of the dryer and cleaning as required at least once per year, or if
performance diminishes. Heavier usage, or an environment that contains excessive lint, dust or other particles,
requires more frequent cleaning. Lint on the air inlet, the Pre-Filters (Dryer or HEPA if so equipped), or other
internal parts of dryer will reduce efficiency and shorten the life of the working parts.
To clean, shut off power to dryer at service connection. Remove Cover by unscrewing the 2 Tamper-Proof Bolts
from side of Cover with the special Tamper-Proof Wrench provided with each dryer. Use a small, soft brush to
gently clean all parts. If your unit contains a dryer Pre-filter or HEPA Filtration System, unclip the Pre-Filter, rinse
the Pre-Filter with water and dry. Re-install.
DO NOT CL EAN THE HEP A F IL TER OR AL L OW IT TO COM E INTO
CONTACT W ITH W ATER.
TROUB L ESHOOTING
SIDE VIEW
FRONT VIEW
FACING WALL
Dryer does not turn on
1. Check power to the unit and connections. Verify dryer is receiving
the correct
voltage at the T
erminal Block
(check dryer label).
2. Check RED service LED light next to air outlet on bottom of dryer for
L i g h t i s ON
– Place hands under Sensor. If light stays on, then replace Sensor.
If light goes off, check to make sure wiring is correct. If OK, check wire
connecting to Motor. If both are OK, replace Motor.
L i g h t i s OF F
– Check for loose, disconnected or improper wiring (See wiring
schematic inside dryer Cover), or replace Control Assembly.
L i g h t i s F L ASHING
– See error codes in CODE chart
SENSOR RANG E ADJ USTM ENT:
If dryer will not turn on, stays on, or stops
working, it may be mounted too close to a counter or object and has gone into
lockout. If relocating appliance is not possible, adjust the range of the Sensor.
Turn off power to dryer then turn the range adjustment on the Control Assembly
counterclockwise towards L (-) low to decrease Sensor range.
Dryer does not shut off
1. May be mounted too close to a counter or object (adjust Sensor range).
2. Check for loose, disconnected or improper wiring at Control Assembly (refer to
wiring schematic affixed to blower housing).
3. Replace Control Assembly.
Dryer does not always turn on, or turns on by itself
1. May be mounted too close to counter or object (adjust Sensor range).
2. Check for foreign material on Optical Sensor next to Air Outlet.
3. Check for loose wires on Control Assembly.
4. Replace Control Assembly.
R E A D A N D S AV E T H E S E I N S T R U C T I O N S
