E X C E L D R Y E R , I N C 1 . 8 0 0 . 2 5 5 . 9 2 3 5 E X C E L D R Y E R . C O M A D M I N @ E X C E L D R Y E R . C O M
3 5 7 C H E S T N U T S T R E E T, E A S T L O N G M E A D O W , M A 0 1 0 2 8
0 2 / 2 0 1 6
2
R E A D A N D S AV E T H E S E I N S T R U C T I O N S
W ARNING :
F o r p r o p e r e l e c t r i c a l c o n n e c t i o n s , c h e c k y o u r l o c a l b u i l d i n g c o d e s .
Your unit must be installed by a qualified, licensed electrician.
P RE INSTAL L ATION W IRING
• Check that the electrical supply corresponds to that shown
on the rating sticker of unit. If the dryer is connected to any
electrical supply other than that stated on the rating sticker of
the unit, permanent damage or improper, unsafe operation of
the unit may result.
• Make sure electricity is switched off at the main panel before
installing, maintaining or cleaning this hand dryer. Dryer must
be installed in accordance with current local wiring and
building regulations.
• Do not wire this hand dryer into the lighting circuit. It must be
protected by an independent circuit.
• Dryer is intended to be permanently connected to power
supply, and must be properly grounded.
SAF ETY
• Troubleshooting and internal maintenance must be performed
by qualified service personnel.
• Do not use any power wash equipment for cleaning on or
near this unit.
• Do not use the XLERATOR dryer for drying hair.
• Do not obstruct air inlets or outlets.
1. Disconnect the power source previously brought to the hand
dryer location (see pre installation wiring above).
2. Use the Tamper-Proof Wrench supplied to remove the 2
cover mounting screws and lift cover to remove from base
plate.
3. If electrical wiring entry is to be made from the rear, remove
the appropriate pre-formed knockout on the base plate. If
entry is to be made from the bottom, knock out the
pre-formed area on the cover for your supply connection.
A rigid conduit must be used.
4. Select the appropriate mounting height for dryer (Table 1)
and fastener, as recommended (Table 2). There should be
no obstruction between the hand dryer and the floor. If
mounting over a countertop, distance from counter to dryer
must be 15” (381 mm) minimum.
CAUTION:
Do not use Base Plate as a guide when drilling.
Make sure no pipe work (gas, water, air) or any electrical cables
or wires are located directly behind the area to be drilled.
5. Attach Base Plate at the four corners to smooth wall.
For most secure installation, use 2 additional mounting holes
as shown in drawing. For non-HEPA units, remove Control
Assembly to access the right side mounting hole.
For HEPA units, remove filter only to access the right side
mounting hole.
6. Identify the voltage of your dryer from the rating sticker of the
unit. Then connect to a dedicated branch circuit not
exceeding 20 Amp.
7. Secure electrical wiring to terminals as indicated by the
schematic affixed to blower housing. An identified ground
connection point is supplied on the Base Plate for your
equipment ground wire. Dryers should be installed per local
code requirements.
8. Carefully replace Cover using the 2 screws previously
removed in step 2. Restore power and test for proper
operation. In multiple installations, make sure the serial
number marked on the inside matches the cover number.
9. It is highly recommended that a bead of silicone sealant be
placed around the outside of the cover at the wall to protect
dryer from internal corrosion caused by wash water and
cleaning solutions.
10. Return Tamper-Proof Wrench
a d
er a al
to owner.
SUG G ESTED M OUNTING HEIG HT
from floor to bottom of dryer:
Men
45" (114 cm)
Women
43" (109 cm)
Teenagers
41" (104 cm)
Small Children
35" (89 cm)
Handicapped
37" (94 cm)
M OUNTING HARDW ARE
Re c o m m e n d e d F a s t e n e r
(not supplied):
Masonry Wall
½” Expansion Sleeve with ¼” Lag Bolt
Hollow Wall
¼” Wing Type Toggle Bolt
Wooden Wall
¼” Lag Screw With Washer
1
2
INSTAL L ATION INSTRUCTIONS
TABLE 1
TABLE 2
IM P ORTANT SAF ETY INSTRUCTIONS
ADJUSTING THE HEAT OUTPUT AND MOTOR SPEED
The dryer is shipped set at maximum heat and motor speed.
To adjust, turn the corresponding knob (H=heater, M=Motor)
on the control assembly counterclockwise to desired setting.
