manualshive.com logo in svg

Excalibur CHLOR-A-SOFT, Инструкция по установке и эксплуатации, Страница: 28 / 31

Поделиться
Скачать
Excalibur CHLOR-A-SOFT Скачать руководство пользователя страница 28

Page 28 

 

The plug and/or injector can be pried out with a small screwdriver/ the plug can be wiped clean. 

If the lug leaks replace the entire plug. The injector consists of a throat and a nozzle. Chemically 
clean the injector with vinegar or sodium bisulfate. The holes can be blown out with air. Both 

pieces have small diameter holes that control the flow rates of water to insure that the proper 

concentration of regenerant is used. Sharp objects, which can score the plastic, should not be 

used to clean the injector. Scoring the injector or increasing  the diameter of the hole could 

change the operating parameters of the injector. 

 
Two holes are labeled DN and UP. Check for compliance with one of the following: 

a.

 

for down flow systems, the appropriate size injector is located in the “D” hole, a plug is in 

the “UP” hole and that the piston is a combination of the down flow main piston and the 

regenerant piston; or 

b.

 

for backwash only systems, a plug is in the “DN” hole and in the “UP” hole, and that the 

piston only has a down flow main piston (the regenerant piston must be removed) and a 
plug is in the refill flow control position. 

 

Push the plug(s) and/or injectors firmly in place, replace the screen and hand tighten the injector 

cap. 

 

Refill Flow Control Assembly or Refill Port Plug 
 

To clean replace the refill flow control, pull out the elbow-locking clip and then pull straight up on 

the elbow. Replace the elbow locking clip in the slot so that it is not misplaced. Twist to remove 

the white flow control retainer. The flow control can be removed by prying upwards through the 

side slots of the retainer with a small blade flat screwdriver. 

 
Chemically clean the flow control or the white flow control retainer using dilute sodium bisulfate 

or vinegar. Do not use a wire brush. If necessary, replace the flow control, o-ring on the flow 

control retainer, or the o-ring on the elbow. 

 

Reset the flow control so the rounded end is visible in the flow control. Reset the white flow 
control retainer by pushing the retainer into the elbow until the o-ring sets. Remove locking clip, 

push down on elbow to reset and insert locking clip. 

 

Do not use Vaseline, oils, or other unacceptable lubricants on o-ring. A silicon lubricant may be 

used on the o-ring on the elbow or the white retainer. 

 

Meter Plug 

 

This control valve does not come equipped with a meter, instead a plug is installed. The plug 

should not need to be serviced.  

 

To remove the meter plug assembly, unscrew the meter cap on the left side of the control valve. 
Pliers may be used to unscrew the nut if necessary. 

 

With the nut removed, a slot at the top of the meter plug is visible. Twist a flat blade screwdriver 

in the slot between the control valve body and the meter plug. When the meter plug is part way 

out it is easy to remove the meter plug from the housing. 

 
Do not use a wire brush to clean. Wipe with a clean cloth or chemically clean in dilute sodium 

bisulfate or vinegar. 

 

Содержание CHLOR-A-SOFT
































Отзывы:

Нет отзывов