EWT Clima 1250 WK, Инструкция по установке и эксплуатации

Страница: 6 / 32

Installation and Operating Instructions
CLIMA....WK Panel Heaters
Model ( s ) Description
Clima 750 WK 750W, Thermostat, On/Off & Heat Selection Switch
Clima 1250 WK 1250W, Thermostat, On/Off & Heat Selection Switch
Clima 2000 WK 2000W, Thermostat, On/Off & Heat Selection Switch
IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
When using electrical appliances, basic precautions should
always be followed to reduce the risk of fire, electrical shock,
and injury to persons, including the following:
IMPORTANT – The wall brackets supplied with the appliance
must be used.
IMPORTANT – If the heater is installed in a room containing
a bath or shower, it must be so installed that switches and
other controls cannot be touched by a person using a bath
or shower.
Do not use outdoors.
Do not locate the heater immediately below a fixed socket
outlet or connection box.
Do not cover the heater. Do not place material or garments on
the heater, or obstruct the air circulation around the heater,
for instance by curtains or pushing furniture up against the
heater, as this could cause overheating and a fire risk.
NEVER cover or obstruct in any way the heat outlet slots at the
top of the heater or the air inlet slots in the base of the heater.
WARNING – THE SURFACES OF THIS HEATER CAN BE
HOT. Momentary contact with any part of the heater should
not cause injury. However, aged or infirm persons or young
children should not be left unsupervised in the vicinity of the
heater unless a suitable guard is fitted.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play
with the appliance.
Note that due care and consideration must be taken when
using this heater in series with a thermal control, a program
controller, a timer or any other device that switches on the
heat automatically, since a fire risk exists when the heater is
accidentally covered or displaced.
If the supply cord is damaged it must be replaced by the
manufacturer or service agent or a similarly qualified person
in order to avoid a hazard.
WARNING: IN ORDER TO AVOID OVERHEATING, DO
NOT COVER THE HEATER.
Electrical
WARNING – THIS APPLIANCE MUST BE EARTHED
The electrical installation must be carried out by a competent
electrician, and be in strict accordance with the current I.E.E.
regulations for Electrical Equipment in Buildings.
The heater is fitted with a length of flexible cable type H05VV-F size 3
x 1.0mm
2
on 0.75kW - 2.0kW models and size 3 x 1.5mm2 on 3.0kW
models, for connection to the fixed wiring of the premises through a
suitable connection box positioned adjacent to the heater.
The supply circuit to the heater must incorporate a double pole isolating
switch having a contact separation of at least 3mm.
Supplementary Earth Bonding
Should Equipotential Earth Bonding be required the earthing
conductor in the supply cord is deemed to provide the supplementary
bonding connection (Please refer to latest Edition of National Wiring
Regulations). A means for disconnection must be incorporated in the
fixed wiring of the premises in accordance with National Wiring Rules.
General
The Panel heater is designed for wall mounting on the wall brackets
supplied. It should only be operated when in the upright position as
shown in Fig 1.
All models are splashproof to IP24 standard.
Before connecting the heater check that the supply voltage is the same
as that stated on the heater.
Wall Mounting
IMPORTANT – The wall brackets supplied with the appliance must
be used. The heater should be positioned observing the minimum
clearances stated around the heater - see Fig. 1 .
DO NOT locate the heater immediately below a fixed socket outlet
or connection box.
1. Remove wall mounting bracket from the back of the heater
by depressing the spring latch at the top of each bracket -
see Fig. 2 .
2. Fix the wall bracket securely to the wall through the four
screw holes provided.
3. Present the heater to the wall bracket, and engage lower
slots in the back with bracket.
4. Raise the heater to upright position and push the heater
onto brackets to engage top latch.
Access to the controls
To open the hinged controls cover, insert the blade of a screwdriver in
the small slot on the right hand side of the cover, and gently turn the
lock in an anti clockwise direction (see Fig. 3). Note: After adjustment
of the controls the control cover must be closed and returned to the
locked position.
GB
3