EWM Taurus 351 Basic FKG Скачать руководство пользователя страница 3

Страница: 3 / 74

Contents

Notes on the use of these operating instructions

099-005425-EW501

14.07.2016

Contents

Contents .................................................................................................................................................. 3

Safety instructions ................................................................................................................................. 6

2.1

Notes on the use of these operating instructions .......................................................................... 6

2.2

Explanation of icons ....................................................................................................................... 7

2.3

Safety instructions .......................................................................................................................... 8

2.4

Transport and installation ............................................................................................................ 12

Intended use ......................................................................................................................................... 13

3.1

Documents which also apply ....................................................................................................... 13

3.1.1

Warranty ....................................................................................................................... 13

3.1.2

Declaration of Conformity ............................................................................................. 13

3.1.3

Welding in environments with increased electrical hazards ......................................... 13

3.1.4

Service documents (spare parts and circuit diagrams) ................................................ 13

3.1.5

Calibration/Validation ................................................................................................... 13

Machine description

– quick overview .............................................................................................. 14

4.1

Front view .................................................................................................................................... 14

4.2

Rear view ..................................................................................................................................... 16

4.3

Inside view ................................................................................................................................... 18

4.4

Machine control

– Operating elements ........................................................................................ 19

Design and function ............................................................................................................................. 21

5.1

Transport and installation ............................................................................................................ 21

5.1.1

Lifting by crane ............................................................................................................. 21

5.1.2

Ambient conditions ....................................................................................................... 22

5.1.2.1

In operation ................................................................................................... 22

5.1.2.2

Transport and storage ................................................................................... 22

5.1.3

Machine cooling ............................................................................................................ 22

5.1.4

Workpiece lead, general ............................................................................................... 22

5.1.5

Welding torch cooling system ....................................................................................... 23

5.1.5.1

Approved coolants overview ......................................................................... 23

5.1.5.2

Maximal hose package length ...................................................................... 23

5.1.5.3

Adding coolant .............................................................................................. 24

5.1.6

Notes on the installation of welding current leads ........................................................ 25

5.1.7

Stray welding currents .................................................................................................. 26

5.1.8

Mains connection .......................................................................................................... 27

5.1.8.1

Mains configuration ....................................................................................... 27

5.1.9

Shielding gas supply (shielding gas cylinder for welding machine) ............................. 28

5.1.9.1

Pressure regulator connection ...................................................................... 28

5.1.9.2

Shielding gas hose connection ..................................................................... 29

5.1.9.3

Gas test

– setting the shielding gas volume ................................................. 30

5.1.9.4

Rinse hose package function ........................................................................ 30

5.2

Welding data display .................................................................................................................... 31

5.3

MIG/MAG welding ........................................................................................................................ 32

5.3.1

Welding torch and workpiece line connection .............................................................. 32

5.3.2

Wire feed ...................................................................................................................... 35

5.3.2.1

Open the protective flap of the wire feeder ................................................... 35

5.3.2.2

Inserting the wire spool ................................................................................. 36

5.3.2.3

Changing the wire feed rollers ...................................................................... 37

5.3.2.4

Inching the wire electrode ............................................................................. 39

5.3.2.5

Spool brake setting ....................................................................................... 40

5.3.3

Welding task selection .................................................................................................. 41

5.3.3.1

Accessory components for operating point setting ....................................... 41

5.3.4

Further welding parameters ......................................................................................... 42

5.3.5

MIG/MAG functional sequences / operating modes ..................................................... 43

5.3.5.1

Explanation of signs and functions ............................................................... 43

5.3.6

Standard MIG/MAG torch ............................................................................................. 45

5.3.7

MIG/MAG special-torches ............................................................................................ 45

5.4

MMA welding ............................................................................................................................... 46

Содержание Taurus 351 Basic FKG











































































Результаты поиска

Содержание Taurus 351 Basic FKG

Отзывы:

Похожие инструкции для Taurus 351 Basic FKG

Бренды по названию

Популярные бренды

EWM Taurus 351 Basic FKG, Руководство по эксплуатации

Результаты поиска

Содержание Taurus 351 Basic FKG

Отзывы:

Похожие инструкции для Taurus 351 Basic FKG

Бренды по названию

Популярные бренды