EWM PM 301 W Скачать руководство пользователя

Страница: 40 / 59

Rectifying faults

Vent coolant circuit

099-700003-EW501

14.09.2020

Unstable arc



Unsuitable or worn welding torch equipment





Adjust contact tip to wire diameter and -material and replace if necessary



Adjust wire guide to material in use, blow through and replace if necessary



Incompatible parameter settings



Check settings and correct if necessary

Pore formation



Inadequate or missing gas shielding



Check shielding gas setting and replace shielding gas cylinder if necessary



Shield welding site with protective screens (draughts affect the welding result)



Unsuitable or worn welding torch equipment



Check size of gas nozzle and replace if necessary



Condensation (hydrogen) in the gas tube



Purge hose package with gas or replace



Splashes in the gas nozzle



Gas distributor out of order or missing

7.2 Vent coolant circuit

To vent the cooling system always use the blue coolant connection, which is located as deep as

possible inside the system (close to the coolant tank)!

Figure 7-1

Complete the following steps to vent the welding torch:
• Connect the welding torch to the cooling unit
• Switch on the welding machine
Venting the welding torch starts and lasts for approx. 5 to 6 minutes.

Содержание PM 301 W




























































Результаты поиска

Содержание PM 301 W

Отзывы:

Похожие инструкции для PM 301 W

Бренды по названию

Популярные бренды

EWM PM 301 W, Руководство по эксплуатации

Результаты поиска

Содержание PM 301 W

Отзывы:

Похожие инструкции для PM 301 W

Бренды по названию

Популярные бренды