EWM PM 221 G Скачать руководство пользователя страница 9

Страница: 9 / 54

Product description – quick reference

Product variants

099-700000-EW501

22.09.2020

Product description – quick reference

4.1 Product variants

Version

Functions

Performance class

Professional MIG

PM221/301/401G,

PM301/451/551W

Water-cooled

You use the torch trigger to switch the welding process on and

off. Interchangeable contact tip holder.

PM301/451/551W

Gas-cooled

You use the torch trigger to switch the welding process on and

off. Interchangeable contact tip holder.

PM221/301/401G

Short torch neck

For welding narrow operating points.

PM451/551W

Extended torch neck

For welding operating points which are difficult to reach.

High duty cycle.

PM451/551W

Interchangeable torch neck

Torch neck can be continuously fixed through 360°.

PM221/301G

PM301/451W

2U/D

2 up/down welding torch

The welding power (welding current/wire feed speed) and the

voltage correction or the JOB number and program number

can be adjusted on the welding torch.

PM221/301/401G,

PM301/451/551W

RD2

Remote display 2-welding torch

The welding power (welding current/wire feed speed) and the

voltage correction or the JOB number and program number

can be adjusted on the welding torch. Values and changes

are shown on the welding torch display.

PM221/301/401G,

PM301/451/551W

RD3

Remote display 3-welding torch

The welding power (welding current / wire feed speed),

welding voltage correction, program number, dynamics and

welding procedure can be changed from the welding torch.

Values, changes, faults and error messages are displayed on

the welding torch display.

PM221/301/401G,

PM301/451/551W

X Technology

Welding torch with X technology – function torch without sepa-

rate control cable

PM221/301/401G,

PM301/451/551W

Содержание PM 221 G























































Результаты поиска

Содержание PM 221 G

Отзывы:

Похожие инструкции для PM 221 G

Бренды по названию

Популярные бренды

EWM PM 221 G, Руководство по эксплуатации

Результаты поиска

Содержание PM 221 G

Отзывы:

Похожие инструкции для PM 221 G

Бренды по названию

Популярные бренды