EWM PM 221 G Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 54

background image

Design and function

Transport and installation

14

099-700000-EW501

22.09.2020

5.1.1.2 Transport and storage

Storage in a closed area, temperature range of the ambient air:

• -25 °C to +55 °C (-13 F to 131 F)

[1]

Relative humidity

• up to 90 % at 20 °C (68 F)

[1]

Ambient temperature dependent on coolant! Observe the coolant temperature range of the torch coo-

ling

5.1.2 Settings

After the torch component has been connected, the control elements of the welding machine control are

no longer in operation, other accessories for remote control must not be connected.
Parameter changes are saved immediately and displayed on the welding machine control!
The full functional range of the PM function torch is only available in connection with the device series

Titan XQ and the wire feeder drive XQ.
If the function torch is connected to another EWM device series using Multimatrix, the welding torch swit-

ches to compatibility mode and is restricted in its functions.
Depending on the torch version, the user can change the following welding parameters of the main pro-

grams.

control welding torch

2U/D

RD2

RD3

Program switching

JOB switching

Process switching

Operating mode

Welding method

Wire feed speed

Voltage correction

Dynamics

5.1.3 Operating elements in the machine

This setting affects the torch types 2U/D, and RD2.

Figure 5-1

• Switch the"Program or up/down mode“ changeover switch at the welding machine to the up/down or

program mode position (see chapter "Design and function").

The 'Program or up/down function' changeover switch may look different on your machine. Use

the operating instructions for your power source to operate the switch.

«
...
12
13
14
15
16
...
»

Содержание PM 221 G























































Отзывы:

Нет отзывов

Похожие инструкции для PM 221 G

Бренд: Vancare Страницы: 31

Бренд: hager Страницы: 8

Бренд: Nelson Страницы: 12

Бренд: Federal Signal Corporation Страницы: 24

Бренд: C-TEC Страницы: 10

Бренд: iLive Страницы: 16

Бренд: Pyle Страницы: 6

Бренд: JBL Страницы: 4

Бренд: ubbink Страницы: 61

Бренд: IDS Страницы: 8

XRX300 LED Series

Бренд: WE-EF Страницы: 6

Бренд: M+S Страницы: 2

FHF DSLB 20 LED

Бренд: Eaton Страницы: 28

SpectrAlert S1224MCW

Бренд: System Sensor Страницы: 4

MultiPRO Series

Бренд: Paton Страницы: 44

AMX ACENDO VIBE ACV-2100

Бренд: Harman Страницы: 41

Бренд: Kenco Страницы: 15

Бренд: Creative Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды