EWM PM 221 G Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 54

background image

Design and function

Transport and installation

16

099-700000-EW501

22.09.2020

Item Symbol Description

0

3

"B +" button (program mode)

Increase JOB number

"B +" button (up/down mode)

Welding voltage correction, increase value

4

"A -" button (Program mode)

Decrease program number

"A -" button (Up/Down mode)

Reduce welding performance (welding current/wire-feed speed)

5

"A +" button (Program mode)

Increase program number

"A +" button (Up/Down mode)

Increase welding performance (welding current/wire-feed speed)

5.1.6 Welding data display

The display shows the currently selected welding parameter and the corresponding parameter value.
When the welding machine is switched on, the display shows the nominal welding current set point set

point set by the control unit.
During the up/down operation, the corresponding parameter value is shown on the display when the para-

meter is changed. If this parameter is not changed for more than approx. 5 s, the display switches back to

the values set by the control unit.

Examples for welding parameters in the welding data display

Welding parameters

Display

Welding current

Wire feed speed

Voltage correction

Programs

JOB number

«
...
14
15
16
17
18
...
»

Содержание PM 221 G























































Отзывы:

Нет отзывов

Похожие инструкции для PM 221 G

Бренд: Panasonic Страницы: 40

Бренд: Panasonic Страницы: 56

Бренд: JBL Страницы: 2

Бренд: JBL Страницы: 4

MME239 - Micro DVD Home Theater System

Бренд: Magnavox Страницы: 41

Бренд: ZKTeco Страницы: 16

Бренд: SMT Страницы: 24

Бренд: Accent Acoustics Страницы: 8

Бренд: Laars Страницы: 9

Бренд: Raychem Страницы: 6

Бренд: Unimig Страницы: 14

Бренд: M-system Страницы: 2

Бренд: EAW Страницы: 2

Бренд: 2N Страницы: 44

Бренд: Grundig Страницы: 16

Бренд: Corbin Russwin Страницы: 8

Бренд: Jet Страницы: 40

Бренд: LEGRAND Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды