EWM Phoenix Expert drive 4L M3.70 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 101

background image

Safety instructions

General

8

099-004846-EW501

8.01.2014

2.3

General

DANGER

Electromagnetic fields!
The power source may cause electrical or electromagnetic fields to be produced which
could affect the correct functioning of electronic equipment such as IT or CNC devices,
telecommunication lines, power cables, signal lines and pacemakers.

•  Observe the maintenance instructions! (see Maintenance and Testing chapter)
•  Unwind welding leads completely!
•  Shield devices or equipment sensitive to radiation accordingly!
•  The correct functioning of pacemakers may be affected (obtain advice from a doctor if

necessary).

Do not carry out any unauthorised repairs or modifications!
To avoid injury and equipment damage, the unit must only be repaired or modified by
specialist, skilled persons!
The warranty becomes null and void in the event of unauthorised interference.

• Appoint only skilled persons for repair work (trained service personnel)!

Electric shock!
Welding machines use high voltages which can result in potentially fatal electric shocks
and burns on contact. Even low voltages can cause you to get a shock and lead to
accidents.

•  Do not touch any live parts in or on the machine!
•  Connection cables and leads must be free of faults!
•  Switching off alone is not sufficient!
•  Place welding torch and stick electrode holder on an insulated surface!
•  The unit should only be opened by specialist staff after the mains plug has been

unplugged!

• Only wear dry protective clothing!
• Wait for 4 minutes until the capacitors have discharged!

WARNING

Validity of this document!
This document is only valid in combination with the operating instructions for the
power source being used (welding machine)!

• Read the operating instructions, in particular the safety instructions for the power source

(welding machine)!

Risk of accidents if these safety instructions are not observed!
Non-observance of these safety instructions is potentially fatal!

•  Carefully read the safety information in this manual!
•  Observe the accident prevention regulations in your country.
•  Inform persons in the working area that they must observe the regulations!

Explosion risk!
Apparently harmless substances in closed containers may generate excessive pressure
when heated.

• Move containers with inflammable or explosive liquids away from the working area!

• Never heat explosive liquids, dusts or gases by welding or cutting!

«
...
6
7
8
9
10
...
»

Содержание Phoenix Expert drive 4L M3.70






































































































Отзывы:

Нет отзывов

Похожие инструкции для Phoenix Expert drive 4L M3.70

Бренд: Technik-Plus Страницы: 29

Бренд: Super Walter Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды