EWM Phoenix Expert drive 4L M3.70 Скачать руководство пользователя страница 53

Страница: 53 / 101

Design and function

TIG welding

099-004846-EW501

8.01.2014

5.8

TIG welding

5.8.1

Welding torch connection

NOTE

TIG welding torches to be connected to a Euro torch connector are available in two
versions:

• TIG combi welding torches are connected to the Euro torch connector of the wire feeder

and to the (-) welding current plug of the power source.

• TIG welding torches of the EZA version are connected to the Euro torch connector of the

wire feeder only. To do so, the welding current lead of the intermediate hose package must
be connected to the (-) welding current connection at the rear of the unit!

Figure 5-17

Item Symbol

Description

Welding torch

Welding torch hose package

Welding torch connection (Euro or Dinse torch connector)

Welding current, shielding gas and torch trigger integrated

Quick connect coupling (blue)

coolant supply

Quick connect coupling (red)

coolant return

"-" welding current connection socket

• TIG welding:

Welding current connection for welding torch

Power source

Содержание Phoenix Expert drive 4L M3.70






































































































Результаты поиска

Содержание Phoenix Expert drive 4L M3.70

Отзывы:

Похожие инструкции для Phoenix Expert drive 4L M3.70

Бренды по названию

Популярные бренды

EWM Phoenix Expert drive 4L M3.70, Руководство по эксплуатации

Результаты поиска

Содержание Phoenix Expert drive 4L M3.70

Отзывы:

Похожие инструкции для Phoenix Expert drive 4L M3.70

Бренды по названию

Популярные бренды