Functional characteristics
Special parameters (advanced settings)
62
099-5TLPXQ-EW501
29.01.2021
5.10.1.14 Block JOB mode (P16)
The following accessory components support block JOB mode:
• Up/Down welding torch with one-digit 7-segment display (two keys)
Program 0 is always active in JOB 0 and program 1 in all other JOBs
In this operating mode, up to 30 JOBs (welding tasks) divided into three blocks can be called up with ac-
cessory components.
The following configurations must be carried out to use the block JOB operation:
• Set the “Program or Up/Down function” changeover switch to “Program”
• Set the JOB list to actual JOB list (special parameter P12 = “1”)
• Enable block JOB mode (special parameter P16 = “1”)
• Switch to block JOB mode by selecting one of the special JOBs 129, 130 or 131.
Simultaneous operation with interfaces such as RINT X11, BUSINT X11, DVINT X11 or digital
accessory components like the R40 remote control is not possible!
Allocation of JOB numbers to the display on the accessory components
JOB no.
Display/selection on the accessory component
0
1
2
3
4
5
6
7
8
9
Special JOB 1
129
141
142
143
144
145
146
147
148
149
Special JOB 2
130
151
152
153
154
155
156
157
158
159
Special JOB 3
131
161
162
163
164
165
166
167
168
169
JOB 0:
This JOB allows you to set the welding parameters manually.
Selection of JOB 0 can be prevented via the key switch or with the "block program 0" parameter (P2).
Key switch position 0, or special parameter P2 = 0: JOB 0 is blocked.
Key switch position 1, or special parameter P2 = 1: JOB 0 can be selected.
JOBs 1-9:
Nine JOBs can be called up in each special JOB (see table).
Nominal values for wire speed, arc correction, dynamics etc must be defined in advance in these JOBs.
This can be done easily with the PC300.NETsoftware.
If the software is not available, user-defined JOB lists can be created in the special JOB areas with the
"Copy to" function. (See explanations about this in the "Switching JOB lists (P12)" chapter)
5.10.1.15 Selecting programs with the standard torch trigger (P17)
Allows you to select a program or switch a program before starting welding.
You switch to the next program by tapping the torch trigger. Once the last enabled program is reached,
you start again at the beginning.
• Program 0 is the first enabled program, provided that it is not blocked.
(see also special parameter P2).
• The last enabled program is P15.
-
If the programs are not limited by special parameter P4 (see special parameter P4).
-
Or if the programs are limited for the selected JOB by the n cycle setting (see parameter P8).
• Welding starts when the torch trigger is held for longer than 0.64 s.
You can select programs with the standard torch trigger in all operating modes (non-latched, special non-
latched. latched and special latched).
5.10.1.16 Mean value display for superPuls (P19)
Function active (P19 = 1)
• For superPuls, the performance
mean value
from program A (P
A
) and program B (P
B
) is shown on the
display (ex factory).
Function inactive (P19 = 0)
• Only the performance of program A is displayed for superPuls.
If the function is enabled and only "000" is shown on the machine display, this is a rare case of an
incompatible system set-up. Solution: Disable special parameter P19.
