background image

FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable for use.  The FCC 
requires the following statement for your information:

This equipment generates and uses radio frequency energy and, if not installed and used properly; that 
is, in strict accordance with the manufacture’s instructions, may cause interference to radio and television 
reception. It has been type tested and found to comply with the limits for a Class B computing device in 
accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable 
protection against such interference in a residential installation. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause interference to radio or 
television reception, which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following measures:

"

If using an indoor antenna, have a quality outdoor antenna installed.

"

Reorient the receiving antenna until interference is reduced or eliminated.

"

Move the radio or television receiver away from the receiver/control.

"

Move the antenna leads away from any wire runs to the receiver/control

"

Plug the receiver/control into a different outlet so that it and the radio or television receiver are on 

different branch circuits. 

If necessary, the user should consult the dealer or an experienced radio/television technician for 
additional suggestions. The user or installer may find the following booklet prepared  by the Federal 
Communications Commission helpful:

“Interference Handbook”

This booklet is available under Stock Number 004-000-00450-7 from the US Government Printing Office, 
Washington DC 20402.

The user shall not make any changes or modifications to the equipment unless authorized by the 
Installation Instructions or User’s Manual. Unauthorized changes or modifications could void the user’s 
authority to operate the equipment and will void the product warranty.

This device complies with Part 15  of the FCC Rules. Operation is subject to the  following two conditions:

     (1) This device may not cause harmful interference, and

     (2) This device must accept any interference received, including interference that may cause 
          undesired operation.

FCC STATEMENT

EWC Controls Inc.   385 Highway 33   Englishtown, NJ 07726   800-446-3110   FAX 732-446-5362     E-Mail- [email protected]

9

Copyright © 2009 EWC Controls All Rights Reserved

FCCID: XLXA3900

 

Содержание EWT-3900 Ultra-Zone











Отзывы: