manualshive.com logo in svg

EWA CORELIS PXIE-1149.1/4E, Руководство пользователя, Страница: 35 / 41

Поделиться
Скачать
EWA CORELIS PXIE-1149.1/4E Скачать руководство пользователя страница 35

 

 Recommended Target Connectors 

27 

Table  A-3  summarizes  the  specifications  for  a  16-pin  TAP  connector  without  latch  ejector.  
Equivalent connectors are available from other manufacturers. 

 

Reference 

Description 

Manufacturer  Part Number 

Flash TAP 

Straight header, 16-pin, 4 wall, with center notch 

3M 

2516-6002UG 

Table A-3.

  Flash Programming TAP 16 Pin Connector 

Table A-4 describes the signals and Corelis recommended values for terminating resistors: 

 

Pin  Signal 

Direction 

Termination 

1 

TRST* 

Input to the UUT  1K pull-up (or 1.5K pull-down) 

2 

GND 

 

 

3 

TDI  

Input to the UUT  1K pull-up 

4 

GND 

 

 

5 

TDO  

Output from UUT  33 ohm series 

6 

GND 

 

 

7 

TMS 

Input to the UUT  1K pull-up 

8 

GND 

 

 

9 

TCK 

Input to the UUT  1K pull-up 

10 

GND 

 

 

11 

Write_Strobe*  Input to the UUT  1K pull-up 

12 

GND 

 

 

13 

Reserved 

 

 

14 

GND 

 

 

15 

Ready/Busy* 

Output from UUT  1K pull-up 

16 

GND 

 

 

Table A-4.

  Signal Description and Termination

 

Note:

    Some  target 

boards may require a 

pull-down resistor on 
the  TRST*  signal  to 

assure  normal  device 
operations  when  not 

in boundary-scan test 
mode 
 

Note:

  The  target 

TDI  signal  is  driven 

by the TDO signal of 
the 

boundary-scan 

controller  
 

Note:

    The  target 

TDO  signal  drives 

the  boundary  scan 

controller’s 

TDI 

signal 
 

Содержание CORELIS PXIE-1149.1/4E










































Отзывы:

Нет отзывов