EWA CORELIS PXIE-1149.1/4E Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 41

EWA CORELIS PXIE-1149.1/4E Скачать руководство пользователя страница 15

PXIEPXIE-1149.1/4E Installation

7

Chapter 2:

PXIE-1149.1/4E Installation

Installing the ScanExpress software and PXIE-1149.1/4E hardware

The PXIE-1149.1/4E product consists of the following components:

•

PXIE-1149.1/4E Hardware

•

PXIE-1149.1/4E

User’s Manual

•

One 80-pin to Four 20-pin TAP Cable, Corelis P/N 15467

Please ensure that all items listed above are present and free from visible damage or defects before

proceeding. If anything appears to be missing or damaged, immediately contact Corelis at the
number shown on the title page of this manual.

Software Must Be Installed.

The PXIE-1149.1/4E installation procedure requires the use of software that contains the driver for

the PXIE-1149.1/4E module. Obtain the ScanExpress CD-ROM (or any other Corelis application
that supports the PXIE-1149.1/4E module) in order to proceed with installation. Install the PXIE-
1149.1/4E controller before installing the ScanExpress Application Software.

PXIE-1149.1/4E Hardware Installation

To install the PXIE-1149.1/4E on a host PC, follow the installation steps below. Plug in the PXIE-
1149.1/4E controller into an available PXIE port on the host PC while powered down. The

following section describes this process in detail for installing using Windows 7 and Windows 10.
Note that depending on the version of Windows used, the procedure may differ slightly.

Installation Steps

1.

While powered down, install the PXIE-1149.1/4E module into the any available PXIE
peripheral slot. Then power on.

2.

Install the application software, such as

“

ScanExpress Runner,

”

from the CD on your

computer.

«
...
13
14
15
16
17
...
»

Содержание CORELIS PXIE-1149.1/4E










































Отзывы:

Нет отзывов