EVSE Viridian EV EPC20 Series Скачать руководство пользователя

Страница: 21 / 22

Issue 1.2 May 2020

EVSE Protocol Controller 2.0 (EPC 2.0) | Viridian EV

SERVICE & MAINTENANCE

8.1 REPLACING THE DEVICE

MAINTENANCE

The Viridian EPC 2.0 charging controller is maintenance

free.

WARNING: THERE ARE NO USER

REPLACEABLE FUSES WITHIN THE EPC

VIRIDIAN EPC 2.0 REPLACEMENT

REQUIREMENT: Ensure that the plant and the device itself are de

energized.

DANGER: VOLTAGE HAZARDS

Contact with live components can result in serious injuries. Disconnect the system and all devices from the power supply
before starting work.

PROCEDURE:

Disconnect the wiring from all EPC 2.0 connector terminals.

Disassemble the device by pulling the locking slider on the back of the device down and swivel the device away from
the DIN rail and remove it.

Install the new device by clipping the top locking guide onto the DIN rail and swinging it down until the locking slider
clicks into place.

Reconnect the wiring.

Switch on the power supply for the device and the main power for the unit feeder again.

8.2 CLEANING

Cleaning of the device is not intended or permissible.

Содержание Viridian EV EPC20 Series























Результаты поиска

Содержание Viridian EV EPC20 Series

Отзывы:

Похожие инструкции для Viridian EV EPC20 Series

Бренды по названию

Популярные бренды

EVSE Viridian EV EPC20 Series, Руководство пользователя

Результаты поиска

Содержание Viridian EV EPC20 Series

Отзывы:

Похожие инструкции для Viridian EV EPC20 Series

Бренды по названию

Популярные бренды