evoralight Roam RGB 44 Series, Инструкция по установке

Страница: 2 / 4

Product Specification Sheet Roam™ RGB 44 Series LED Tape Light
EVORALIGHT.COM
844.964.1600 info@evoralight.com
02
Compatible Drivers
Mean Well™ HLG Driver
Mean Well™ LPV Driver
HLG-40H-24A
HLG-60H-24A
HLG-100H-24A
HLG-120H-24A
HLG-185H-24A
HLG-240H-24A
HLG-320H-24A
HLG-600H-24A
X
X
X
X
X
L: 6 3/4" W: 2 1/2" H: 1 1/2"
L: 6 3/4" W: 2 1/2" H: 1 1/2"
L: 8 5/8" W: 2 11/16" H: 1 1/2"
L: 8 5/8" W: 2 11/16" H: 1 1/2"
L: 9" W: 2 11/16" H: 1 1/2"
L: 9 5/8" W: 2 11/16" H: 1 1/2"
L: 9 7/8" W: 3 1/2" H: 1 3/4"
L: 11" W: 5 5/8" H: 1 7/8"
1 - 7 ft
8 - 12 ft
13 - 19 ft
20 - 24 ft
25 - 36 ft
37 - 48 ft
49 - 67 ft
68 - 120 ft
LPV-35-24
LPV-60-24
L: 5 7/8" W: 1 9/16" H: 1 1/8"
L: 5 7/8" W: 1 9/16" H: 1 1/8"
5 - 7 ft
8 - 12 ft
Power Supply
LED Tape
Length
Product SKU Class 2 Dimensions Diagram
DC AC
**
*
Be sure no more than 5 amps is run through any solderless connector.
Calculate max length of LED tape to follow the solderless connector based on an amperage draw of 0.18 A/ft (0.60 A/m).
Connectors
Installation
Type
EVO-4-C-0
EVO-4-C-36
EVO-4-J-06
EVO-4-J-0
Two Conductor Connector with no wire
Two Conductor Connector with 36" wire
Two Conductor Jumper Connector 6" wire
Two Conductor Jumper Connector with no wire
SKU Description Wire Gauge Mockup
01 02 03 04
R
G
B
+
Peel off
adhesive here
3M
3M
20 AWG
Remove 1/4" of 3M adhesive tape
on the back from the end of the strip
that you want to connect. It must be
removed to allow it to fit properly
with the solderless connector.
Double check the polarity of the
tape to match the positive (+)
markings together and negative (-)
markings together. If you
accidentally close the connector
before you’re ready, you can use a
small flathead screwdriver to pry the
top back open.
Open the top of the EVO connector
and insert the LED tape inside.
Make sure the LED tape is facing
up towards the translucent top and
the solder pads are directly above
the small hooks on the connector.
Once everything is in order, use
pliers to close and lock the
connector. You may hear a “click”
sound when it is properly closed.
Attaches LED tape directly to a
Power Supply/Driver, low
voltage control, or DC source.
Attaches two sections of LED
tape together. Wire lead allows
for turns around tight corners.
Attaches two sections of LED
strip together in a continuous
run.