evoheat CS-i 250, Руководство по установке и эксплуатации

Страница: 17 / 27

info@evoheat.com.au
1300 859 933 www.evoheat.com.au
CS-i Series Manual
Page 16
Syst2:Comp. IPM Over-temp.
Prot.
F255
Syst2 compressor running current is too
large Check if there is a gap in the installation of the
fluorine-cooled heat sink
Syst2:Comp. Overcurrent Prot. F256
Syst2 compressor drive board has poor
heat dissipation
Check if the pressure ratio is too high
Syst2:Comp. Bus Over Voltage F257 Voltage is too high Check if the input voltage is higher than 480V
Syst2:Comp. Bus Under Voltage F258 Voltage is too low Check if the input voltage is lower than 250V
Syst3:Inventer Board Comm.
Failure
F351
Communication failure with syst3
compressor drive board
1. Check if the communication line is normal
2. Check If the syst3 compressor drive board is
normal
Syst3:Compressor start Failure F352 Syst3 compressor failed to start
1. Check if the compressor line is normal;
2. Check if the syst3 compressor is blocked
Syst3:Start IPM Prot. F353
Syst3 compressor starting current is too
large
1. Check if the starting high pressure is
excessive;
2. Check if the syst3 compressor is blocked
Syst3:Running IPM Prot. F354
Syst3 compressor running current is too
large
Check if the pressure ratio is too high
Syst3:Comp. IPM Over-temp.
Prot.
F355
Syst3 compressor running current is too
large Check if there is a gap in the installation of the
fluorine-cooled heat sink
Syst3:Comp. Overcurrent Prot. F356
Syst3 compressor drive board has poor
heat dissipation
Check if the pressure ratio is too high
Syst3:Comp. Bus Over Voltage F357 Voltage is too high Check if the input voltage is higher than 480V
Syst3:Comp. Bus Under Voltage F358 Voltage is too low Check if the input voltage is lower than 250V
Syst2:Inventer Board Comm.
Failure
F451
Communication failure with syst4
compressor drive board
1. Check if the communication line is normal
2. Check If the syst4 compressor drive board is
normal
Syst2:Compressor start Failure F452 Syst4 compressor failed to start
1. Check if the compressor line is normal;
2. Check if the syst4 compressor is blocked
Syst2:Start IPM Prot. F453
Syst4 compressor starting current is too
large
1. Check if the starting high pressure is
excessive;
2. Check if the syst4 compressor is blocked
Syst2:Running IPM Prot. F454
Syst4 compressor running current is too
large
Check if the pressure ratio is too high
Syst2:Comp. IPM Over-temp.
Prot.
F455
Syst4 compressor running current is too
large Check if there is a gap in the installation of the
fluorine-cooled heat sink
Syst2:Comp. Overcurrent Prot. F456
Syst4 compressor drive board has poor
heat dissipation
Check if the pressure ratio is too high
Syst2:Comp. Bus Over Voltage F457 Voltage is too high Check if the input voltage is higher than 480V
Syst2:Comp. Bus Under Voltage F458 Voltage is too low Check if the input voltage is lower than 250V
Fan Motor 1 Output Out Phase F101 System 1 fan failed to start Check if the system 1 fan line is normal
Fan Motor 1 Output Zero Speed F102 System 1 fan failed to start Check if the system 1 fan rotor is locked
Fan Motor 1 Start IPM Prot. F103 System 1 fan starting current is too large Check if the system 1 fan rotor is locked
Fan Motor 1 Running IPM Prot. F104 System 1 fan running current is too large Check if the system 1 fan rotor is locked
Fan Motor 1 Overcurrent Prot. F105 System 1 fan running current is too large Check if the system 1 fan rotor is locked
Fan Motor 1 Over-temp. Prot. F106
System 1 fan drive board has poor heat
dissipation
Check the heat dissipation condition
Fan Motor 1 Bus Over Voltage F107 Voltage is too high Check if the input voltage is higher than 480V
Fan Motor 1 Bus Under Voltage F108 Voltage is too low Check if the input voltage is lower than 250V
Fan Motor 2 Output Out Phase F201 System 2 fan failed to start Check if the system 2 fan line is normal
Fan Motor 2 Output Zero Speed F202 System 2 fan failed to start Check if the system 2 fan rotor is locked
Fan Motor 2 Start IPM Prot. F203 System 2 fan starting current is too large Check if the system 2 fan rotor is locked
Fan Motor 2 Running IPM Prot. F204 System 2 fan running current is too large Check if the system 2 fan rotor is locked
Fan Motor 2 Overcurrent Prot. F205 System 2 fan running current is too large Check if the system 2 fan rotor is locked
Fan Motor 2 Over-temp. Prot. F206
System 2 fan drive board has poor heat
dissipation
Check the heat dissipation condition
Fan Motor 2 Bus Over Voltage F207 Voltage is too high Check if the input voltage is higher than 480V
Fan Motor 2 Bus Under Voltage F208 Voltage is too low Check if the input voltage is lower than 250V