Evo HE H12, Инструкция по установке и обслуживанию

Страница: 7 / 56

7 evo HE H -
Installation & Servicing
GENERAL
INTRODUCTION
The evo HE range of boilers are a fully automatically controlled,
wall mounted, low water content, balanced flue, fanned,
condensing gas boiler. It has full modulating central heating
outputs of :
H12 9.3 kW (32,000 Btu/h) to 12 kW (41,000 Btu/h).
H16 8.8 kW (30,000 Btu/h) to 16.1 kW (55,000 Btu/h).
H19 8.8 kW (30,000 Btu/h) to 19.0 kW (65,000 Btu/h).
H22 8.8 kW (30,000 Btu/h) to 22.0 kW (75,000 Btu/h).
Due to the high efficiency of the boiler a plume of water vapour
will form at the flue terminal during operation depending on
external conditions.
The boiler casing is of white painted mild steel with the user
controls capable of being mounted remotely from the boiler, if
the option is required.
The heat exchanger is of cast aluminium.
Note.
These boilers cannot be used on systems which include gravity
circulation.
The boilers are suitable for connection to fully pumped, open
vented or sealed water systems. Adequate arrangements for
completely draining the system by provision of drain cocks
MUST be provided in the installation pipework.
SAFE HANDLING
This boiler may require 2 or more operatives to move it to its
installation site, remove it from its packaging base and during
movement into its installation location. Manoeuvring the boiler
may include the use of a sack truck and involve lifting, pushing
and pulling.
Caution should be exercised during these operations.
Operatives should be knowledgeable in handling techniques
when performing these tasks and the following precautions
should be considered:
•
Grip the boiler at the base.
• Be physically capable.
• Use PPE as appropriate, e.g. gloves, safety footwear.
During all manoeuvres and handling actions, every attempt
should be made to ensure the following unless unavoidable
and/or the weight is light.
•
Keep back straight.
• Avoid twisting at the waist.
• Avoid upper body/top heavy bending.
• Always grip with the palm of the hand.
• Use designated hand holds.
• Keep load as close to the body as possible.
• Always use assistance if required.
OPERATION
When there is a demand for heat, the heating system is supplied
at the selected temperature of between 30
o
C and 82
o
C.
The boiler features a comprehensive diagnostic system which
gives detailed information on the boiler status when operating,
and performance of key components to aid commissioning and
fault finding.
OPTIONAL EXTRA KITS
z Flue Extension Ducts (1000mm long up to 6m)
z Flue Finishing Kit
z 90
o
Elbow Kit (maximum 4 elbows per installation).
z
45
o
Elbow Kit (maximum 4 elbows per installation).
z Roof Flue Kit (to a maximum of 7.5m)
z Powered Vertical Flue Kit 5m primary and 17m secondary is
a typical maximum length. For alternative maximum lengths
refer to Powered Vertical Instructions.
z High Level Flue Outlet Kits
z
Flue Deflector Kit
z Weather Collar
z Twin Fluing Kits (to a maximum of 60m combined total of
flue and air ducts)
z Horizontal Flue Terminal 600mm long.
z Remote User Control Kit
z Boiler Stand-off Kit
z Siphon Kit
z Condensate Pump Kit
SAFETY
Current Gas Safety (Installation and Use) Regulations or
rules in force.
The appliance is suitable only for installation in GB and IE and
should be installed in accordance with the rules in force.
In GB, the installation must be carried out by a CORGI
Registered Installer. It must be carried out in accordance with
the relevant requirements of the:
•
Gas Safety (Installation and Use) Regulations
• The appropriate Building Regulations either The Building
Regulations, The Building Regulations (Scotland), Building
Regulations (northern Ireland).
• The Water Fittings Regulations or Water byelaws in
Scotland.
• The Current I.E.E. Wiring Regulations.
Where no specific instructions are given, reference should be
made to the relevant British Standard Code of Practice.
In IE, the installation must be carried out by a Competent
Person and installed in accordance with the current edition of
I.S.813 "Domestic Gas Installations", the current Building
Regulations and reference should be made to the current ETCI
rules for electrical installation.
Detailed recommendations are contained in the following British
Standard Codes of Practice:
BS. 5440:1 Flues (for gas appliances of rated input not
exceeding 70 kW).
BS. 5440:2 Ventilation (for gas appliances of rated input not
exceeding 70 kW).
BS. 5449 Forced circulation hot water systems.
BS. 5546 Installation of gas hot water supplies for
domestic purposes (2nd Family Gases).
BS. 6798 Installation of gas fired hot water boilers of rated
input not exceeding 60 kW.
BS. 6891 Low pressure installation pipes.
Health & Safety Document No. 635
The Electricity at Work Regulations, 1989.
The manufacturer’s notes must NOT be taken, in any way, as
overriding statutory obligations.
IMPORTANT. These appliances are CE certificated for safety
and performance. It is, therefore, important that no external
control devices, e.g. flue dampers, economisers etc., are
directly connected to these appliances unless covered by these
Installation and Servicing Instructions or as otherwise
recommended by
Wolseley Centers Ltd. in writing. If in doubt
please enquire.
Any direct connection of a control device not approved by
Wolseley Centers Ltd. may invalidate the certification and the
normal appliance warranty. It could also infringe the Gas Safety
Regulations and the above regulations.
203323-2.pmd 21/09/2007, 11:26 7