Evinrude E-TEC G2 Скачать руководство пользователя страница 43

Страница: 43 / 92



Tilting and Trim

Impact Damage Protection

Your outboard has a shock absorption system

designed to help withstand damage from im-

pact with underwater objects at low to moder-

ate speeds. High speed impacts with rigid

underwater objects like pilings or boulders

can be beyond the capability of the absorption

system. Such impacts can result in serious

damage to your outboard and injury to boat

occupants from the outboard or its parts en-

tering the boat. Occupants can also be eject-

ed or injured by falling against portions of the

boat as a result of rapid deceleration following

impacts.
When boating in unfamiliar, shallow, or de-

bris-laden waters, seek information on safe

boating areas and navigation hazards from a

reliable local source. Reduce your speed and

keep a sharp lookout!

IMPORTANT:

Impact damage is NOT cov-

ered by the outboard warranty.

If you hit any object:
• STOP immediately and examine the out-

board for loosening of attaching hardware.

• INSPECT for damage to swivel and stern

brackets, and steering components.

• EXAMINE the boat for structural damage.

• TIGHTEN any loosened hardware.
If the collision occurred in the water, proceed

slowly to harbor. Before boating again, have

your service technician thoroughly inspect all

components.

007021

NOTICE

The outboard’s shock absorption system

does not work while operating in

reverse. If you back into an object, either

in the water or while trailering, your boat

and outboard can be seriously damaged.

DR4412



WARNING

Failure to inspect for damage after an

accident or striking an object could

result in sudden, unexpected component

failure, loss of boat control, and personal

injury. Unrepaired damage could reduce

your boat and outboard’s ability to resist

future impacts.

Содержание E-TEC G2





























































































Результаты поиска

Содержание E-TEC G2

Отзывы:

Похожие инструкции для E-TEC G2

Бренды по названию

Популярные бренды

Evinrude E-TEC G2, Руководство пользователя

Результаты поиска

Содержание E-TEC G2

Отзывы:

Похожие инструкции для E-TEC G2

Бренды по названию

Популярные бренды