Evinrude E-TEC G2 Скачать руководство пользователя страница 3

Страница: 3 / 92

Easy to Own and Operate

• Three-Year Limited Warranty

• No Scheduled Dealer Maintenance for

Three Years of Normal Recreational Use

• No Operational Break-In Procedure

• Easy Starts (no choking or priming)

• Digital Engine Management

• Self Flushing Cooling System

• Long Term Storage Design

• Simplified Winterization Procedure

• Digital Diagnostics

• Low Oil Usage

Durable and Reliable

• Full Corrosion Protection

•

Evinrude E-TEC

Lubrication System

• Auto-Calibrated Linkage

• Robust, Heavy-Duty Design

• Posi-Lock Latches

• Extra Capacity Water Pump

• Iridium Spark Plugs

• Vibration Isolated Electronics

• Beltless 15 Amp Charging System

• Stainless Steel Thermostat

• Nickel/Chrome-Faced Piston Rings

• Micro Finished Connecting Rods/Crankshaft

Cleaner and Quieter

• EPA Emissions Compliance

• European Union Emissions Compliance

• California 3-Star Emissions Compliance

• Sealed Fuel System

• Low Friction Design (No powerhead

gears, belts, cams, oil scraping rings,

or mechanical oil pump)

• Full Length Insulated Lower Pans

• Quiet Signature Sound

• Air Intake/Silencer

• Idle Air Bypass

Features at a Glance

The following trademarks are the property of Bombardier Recreational Products Inc. or its affiliates:

Evinrude®

Evinrude®/Johnson® XD30™

S.A.F.E.

™

Evinrude® E-TEC®

BRP Logo

SystemCheck

™

Evinrude®/ Genuine Parts

2+4™ Fuel Conditioner

Triple-Guard™

Grease

Evinrude®/ XD100™

HPF Pro™

Gearcase Lubricant

Evinrude®/ XD50™

Содержание E-TEC G2





























































































Результаты поиска

Содержание E-TEC G2

Отзывы:

Похожие инструкции для E-TEC G2

Бренды по названию

Популярные бренды

Evinrude E-TEC G2, Руководство пользователя

Результаты поиска

Содержание E-TEC G2

Отзывы:

Похожие инструкции для E-TEC G2

Бренды по названию

Популярные бренды