Evikon PluraSens E2648-NH3-E Скачать руководство пользователя | Manualshive

Страница: 12 / 21

background image

E2648-NH3-E

Rev 22.06.2021

NOTE! The outputs are not galvanically isolated from the external power supply and share
a common 0V. Allowed load resistance limits are stated in the Speciﬁcations table. To
power the instrument from an external power source, connect terminals 0V and +U to the
source. If the integrated mains power supply module is used, connect terminals L and N to
the mains.

NOTE! Actuator short-circuits should be avoided, to protect the instrument relays using
external fuses or safety switches.

Correct and incorrect cabling for 24 VAC

12

«
...
10
11
12
13
14
...
»

Содержание PluraSens E2648-NH3-E






















Отзывы:

Нет отзывов

Похожие инструкции для PluraSens E2648-NH3-E

Бренд: Nautel Страницы: 229

Бренд: Nautel Страницы: 18

Бренд: Nautel Страницы: 326

Бренд: Yaesu Страницы: 17

Бренд: TILLQUIST Страницы: 15

Gewa Control Easy HM

Бренд: Abilia Страницы: 12

Quantec QT412RXA

Бренд: C-TEC Страницы: 2

Бренд: Mighty Mule Страницы: 2

Бренд: Apache Labs Страницы: 67

Бренд: sebaKMT Страницы: 46

Бренд: Camille Bauer Страницы: 33

Бренд: QRP Labs Страницы: 66

Бренд: Yaesu Страницы: 68

Бренд: Allen-Bradley Страницы: 4

Бренд: Dwyer Instruments Страницы: 4

Бренд: Cisco Страницы: 24

Бренд: Cisco Страницы: 10

DWDM-XENPAK Series

Бренд: Cisco Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды