evertz 5782DEC Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 60

background image

5782DEC

Professional H.264 and MPEG-2 Decoder

Page - 10

Revision 1.0

VLPRO INTERFACE

Decoder Reboot:

This control allows the user to power cycle the decoder.

Load Factory Configuration:

This control allows the user to soft reset the decoder to the factory

settings.

Control Port:

Currently unused on 5782DEC platform.

Data Port <1,2> Control

IP Address:

This control allows the user to set the IP address on the Data Port. This control will also

display the currently set IP address.

Netmask:

This control allows the user to set the Netmask for the Data Port IP address. This control

will also display the currently set Netmask.

Gateway:

This control allows the user to set the Gateway for the Data Port. This control will also

display the currently set Gateway.

Data Port <1,2> Monitor

SFP Part Number:

This parameter returns the part number of the SFP located in the Data Port.

Port Link Status:

This parameter returns the link status for the data port, communicating to the user

whether the link is up or down.

Port Link Info:

This parameter returns the link status for the data port, containing information about

speed and duplex.

Receive Bandwidth:

When the link is Up, this parameter returns the receive bandwidth currently

being read on the Data Port. Reading is in kbps.

Transmit Bandwidth:

When the link is Up, this parameter returns the transmit bandwidth currently

being sent on the Data Port. Reading is in kbps.

Syslog Configuration

Syslog is a valuable tool for debugging the device operation. It is essentially serial readouts over IP,
sent to a dedicated server. If issues are present, Evertz can help install and setup a syslog server for
constant monitoring of the device activity.

External Syslog:

This parameter allows the user to enable or disable sending syslog information to

the configured external server.

Syslog Server IP:

This parameter allows the user to assign the external syslog server IP address.

This will be the address of a PC with the syslog server software installed (e.g. Kiwi Syslog Server).

Temperature

Temperature Monitor:

This displays the temperature of the module.

«
...
18
19
20
21
22
...
»

Содержание 5782DEC





























































Отзывы:

Нет отзывов

Похожие инструкции для 5782DEC

Бренд: Samson Страницы: 28

Бренд: Baldor Страницы: 32

Бренд: EAS Electric Страницы: 4

Бренд: EAS Electric Страницы: 31

Бренд: EAST COAST Страницы: 10

Power Inverter PNVS4

Бренд: Pyle Страницы: 1

Бренд: Snell & Wilcox Страницы: 51

Бренд: ORO Страницы: 18

Бренд: Allied Telesis Страницы: 50

DataBender CVX-1300

Бренд: Cypress Страницы: 28

Бренд: Reach Страницы: 13

Бренд: National Instruments Страницы: 4

Бренд: SunSynk Страницы: 10

Бренд: GMI Страницы: 9

S-1000MM-M2xx05

Бренд: Perle Страницы: 12

Бренд: Zamp Solar Страницы: 9

Бренд: Littfinski Daten Technik Страницы: 2

Бренд: Lindy Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды