EverSewn Sparrow QE Скачать руководство пользователя страница 43

Страница: 43 / 48

1. Remove the extension table, the needle, presser

foot and holder. Remove the bobbin cover and

bobbin. Remove the screws holding the needle

plate.

: Driver for needle plate

2. Remove the needle plate by lifting up the right

side of the plate.

Lift up the bobbin holder (

) and remove it.

: Thread cutter device

4. Clean the hook race ( ), feed dogs and bobbin

holder. Also clean them, using a soft, dry cloth.

5. Replace the bobbin holder into the hook race so

that the tip (

) fits to the stopper (

) as shown.

6. Replace the needle plate inserting the hook ( ) and

holes ( ) into the machine. Retighten the screws.

MAINTENANCE

CAUTION: To prevent accidents.

Remove the needle plate and clean the hook race

and the fabric feed dock regularly.

DANGER: To reduce the risk of

electric shock.

Remove the bobbin cover and the bobbin, and clean

them with the accessory brush.

Bobbin holder

NOTE:

This machine is using LED light to light up stitching

area. If it is not light up, call your dealer.

* There is no need to lubricate this machine.

* If the machine gets dirty, soak a soft cloth with

a small amount of mild detergent and wipe well.

Don't use thinner and benzine.

A. BOBBIN HOLDER

B. HOOK RACE AND FEED DOG

There is a thread cutter device at the lower left of

the fabric feed dogs under the needle plate. Pay

attention because sharp parts are there. Do not

touch the thread cutter device directly.

Disconnect the power line plug from electric

outlet before carrying out any maintenance.

Содержание Sparrow QE

















































Результаты поиска

Содержание Sparrow QE

Отзывы:

EverSewn Sparrow QE, Инструкция по эксплуатации, Страница: 43 / 48

Результаты поиска

Содержание Sparrow QE

Отзывы: