background image

By

Installation / Operation Manual - Emergency Lighting 

Central Inverter System

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed 
including the following:

READ AND FOLLOW ALL SAFETY 
INSTRUCTIONS

A. Do not use outdoors
B. Do not mount near gas or electric heaters.
C. Use caution when servicing batteries. Battery acid can cause burns to skin and eyes. If
acid is spilled on skin or in eyes, flush acid with fresh water and contact a physician
immediately.
D. Equipment should be mounted in locations and at heights where it will not readily be
subjected to tampering by unauthorized personnel.
E. The use of accessory equipment not recommended by the manufacturer may cause an
unsafe condition.
F. Do not use this equipment for other than intended use.

This unit contains lethal voltages.  There are no user serviceable parts inside. Only authorized 
service personnel are to be used for service.

SAVE THESE INSTRUCTIONS

The installation and use of this product must comply with all national, federal, state, municipal 
or local codes that apply. Please read this manual thoroughly before installing and operating 
the Lite-Minder Central Inverter System.
 For assistance please call  technical service at 800-

967-5573 

and speak to a technician 

during normal business hours (EST).

EVENLITE - Life Safety Lighting Solutions - 2575 Metropolitan Dr, Trevose, PA 19052 - 

www.evenlite.com

Lite-Minder

Pg. 1

Содержание Lite-Minder

























Отзывы: