manualshive.com logo in svg

EVAPCO PulsePure Integrated Controller-2, Дополнение к инструкции по эксплуатации и установке

Поделиться
Скачать
EVAPCO PulsePure Integrated Controller-2 Скачать руководство пользователя страница 16

14 

 

 

Local Password

 

Enable Security. Select Local Password from Menu. The user can enter their own Local Password (up to 
10 digits). Accept the new Password by touching the Confirm icon. 

Record the new passcode and keep it 

in a safe place. The Factory cannot reset forgotten or lost Local Passwords.  

 

5.2.3 Display Settings 

 
Note: Changing “Home” Screen display assignments may affect operation. Do not attempt to 
modify the settings without prior approval from Evapco Water Systems.  
 
Adjust Display 

From the Main Menu screen, select Configuration Settings. Select Display Settings. Touch the Scroll 
Down icon until Adjust Display is observed and select it. Adjust Brightness and contrast slide bar to 
achieve desired appearance. When complete select the Confirm icon to accept the change. 

 
Key Beep 

Key Beep factory default setting is disabled. To enable, select Configuration on the Main Menu. Select 
Display Settings. Touch the Scroll Down Button until Key Beep is displayed and select. Select Enabled 
and press the Confirm icon to accept the change. 

 

5.2.4 File Utilities 

The controller collects and stores data for user download to a standard USB flash drive. The controller has 
three logs, Datalog, Event Log, and Reset Log.  All files are in a CSV  format that may be opened in a 
spreadsheet such as Microsoft Excel. 

 

Datalog

 

Contains the following data taken at 1-hour intervals for the past two months: 

Conductivity 

Conductivity Set Point Temperature               

Water Meter 1 and 2 Totals (if equipped) 

After two months, the oldest data will be overwritten with new data. The file will  always 
contain the last two months of data.

 

Event Log

 

Records set point changes, user calibrations, alarms, relay status changes (noted by change from 0 
to 1 in log), file exports, etc. 

System Log  

 

This records hardware changes, automatic calibrations, power loss, etc.. 

 

Data Log Range 

The controller default setting is 2 months. To change, select Configuration from the Main Menu screen. 
Select File Utilities. Select Data Log Range. Ranges from 

“

Since Previous

”

 to 3 Months are available for 

the User to select. Touch the desired range and select the Confirm icon to accept. 
 

Log Frequency 

The controller default setting is 1 hour. To change, select Configuration from the Main Menu screen. 
Select File Utilities. Select Log Frequency. The controller data log frequency selections range from 15 
minutes to 1 Day.  

 
 
 
 
 
 

Содержание PulsePure Integrated Controller-2



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды