Eurotherm Drives 635 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 79

background image

Product-manual Model: 635/DER u. 635/K DER

07-01-05-06-E-V1002.doc

49

6 Wiring

instructions

6.1

General Information

Digital servo drives are designed for

operation in metallic grounded enclosures

.

For perfect operation as well as for observance of all regulations the

front board must be

connected with the enclosure electrically and fixed.

6.2

Control cabling

Recommended cross section 0,25 mm².The control signal lines must be laid seperate from the
power signal lines.(see chapter 6.7.1)
The resolver cable should contain three shielded pairs

and

be shielded as a whole. The shielding

should be connected to the ground spread out on the regulator side.We recommend using
Eurotherm resolver cable

KIR.

Cable for transmitting data are always to be laid shielded !

6.3

Power cabling

Recommended section according to rated current. Use only 75° Cu-cables.

6.4

Installation of the rack

When the rack is secured not in a hinged bay but on a mounting plate, it is recommended to do the
wiring of the connections for the power connector X50 on the rear of the rack before installing.
With hinged-bay installation, the customer must ensure that the parts sensitive to voltage such as the
Ucc bus, mains supply lines, etc., are protected against electric shock.

6.5

Analog setpoint

The setpoint input is a differential input. Therefore the poling can be done depending on the
requirements.
Important: the setpoint voltage must be galvanically connected to the reference potential of the
control connections (plug X10). It is possible to connect one pole directly to GND.

6.6

Safety rules

CAUTION !

Plug / unplug all modules only when
Ucc (DC-BUS) is off, that is, the green LED on the power supply module is off and the
discharge time > 3 minutes has elapsed.
The user must ensure protection against accidental touching.

6.7

Electromagnetic compatibility (EMC)

Confirmity in accordance with the EEC Directive 89/336/EEC has been evaluated using a
reference-system, consisting of a compact type drive and a line-filter on mounting-plate,
connected to an AC-syncronous motor.
Mainly responsible for EMC-emissions is the motor cable. So this has to be installed exeptional
carefully.
The layout of grounding is very important. Grounding has to be low-impedant for high frequences.
That means, all ground-connecting parts have to use area.
The measurements made are valid under the use of Eurotherm - cables, suppression aids and line
filters and by application of the following wiring instructions:

«
...
47
48
49
50
51
...
»

Содержание 635
















































































Отзывы:

Нет отзывов

Похожие инструкции для 635

Micropump I-Drive IMS

Бренд: Idex Страницы: 21

Бренд: Tandon Страницы: 105

Бренд: Motor Power Company Страницы: 23

Бренд: Moog Страницы: 909

ADV200-SI Series

Бренд: gefran Страницы: 14

Бренд: YAKOTEC Страницы: 26

Бренд: agrifac Страницы: 26

Бренд: KB Electronics Страницы: 24

Бренд: KB Electronics Страницы: 39

Allen-Bradley PowerFlex 520 Series

Бренд: Rockwell Automation Страницы: 272

CompletePower Plus CPP-A24V80A-SA-CAN

Бренд: ElectroCraft Страницы: 47

Бренд: TPM Страницы: 28

Бренд: LinMot Страницы: 91

Бренд: Melec Страницы: 39

SERVOSTAR CD-LITE

Бренд: Danaher Motion Страницы: 49

VLT Integrated Servo Drive ISD 510 System

Бренд: Danfoss Страницы: 86

BTL5-H1 M Series

Бренд: Balluff Страницы: 16

Бренд: Festo Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды