Eurotherm Drives 635 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 79

background image

Product-manual Model: 635/DER u. 635/K DER

07-01-05-06-E-V1002.doc

43

4

Mechanical installation

4.1

Mounting

Eurotherm digital servo drives may be installed only in a vertical position to guarantee the best air
circulation for the cooling ribs of the heat sink. Vertical installation above other drive racks or
above other heat producing devices can lead to overheating. In addition the drives are to be
operated exclusively in Eurotherm racks or the compact enclosure respectively.

4.2

Control cabinet - mounting

Installation should be carried out only in a control cabinet in which the inside must be free from
dust, corrosive fumes, gases, and all liquids.

Make absolutely sure that the condensing of evaporating liquids including atmospheric moisture, is
avoided. Should the digital servo drive be installed in a place where condensation is likely, a
suitable anticondensation heater must be installed. The heater must be SWITCHED OFF during
normal operation.
Automatic switch off is recommended.
Eurotherm-digital servo drives should not be installed in are as which have been classified as
dangerous, if they have not been installed in an approved enclosure an accordance with regulations
and checked.

Make sure, there is enough cooling and space !(see sketch)

Ø

only horizontal !

Ø

on the side
no distance is required

rack

100 mm space

100 mm space

Servo-drives

635

above

below

General rule

:

It is better to place heat-producing devices low in an enclosure to support internal convection and
to spread the heat. If placing such devices up high is unavoidable, enlarging the upper dimensions
at the expense of height or installing fans should be considered.

4.3

Cooling

The digital servo drives are protected against damages caused by overheating.
There is a thermal sensor installed on the heat sink. When the temperature rises to >95°C,
the drive is automatically switched off. This setting cannot be changed.
Make sure a cabinet of proper size is selected for adequate air circulation.

If the device becomes operated in a not ventilated device, the case volume of the specified
control cabinet must be calculated in accordance with the following table !

Device

Volume/control cabinet

635/K DER01...DER10

0,12 m³

For more exact information, please, address to the control-cabinet manufacture

«
...
41
42
43
44
45
...
»

Содержание 635
















































































Отзывы:

Нет отзывов

Похожие инструкции для 635

ADAP-KOOL AKD 102

Бренд: Danfoss Страницы: 130

DFPI-xxx-ND2P-E-NB3 Series

Бренд: Festo Страницы: 4

Бренд: Lenze Страницы: 210

Бренд: EKSMA OPTICS Страницы: 12

SINAMICS S210 FSA

Бренд: Siemens Страницы: 2

MICROMASTER 6SE92

Бренд: Siemens Страницы: 2

SIMODRIVE POSMO SI

Бренд: Siemens Страницы: 2

Бренд: Siemens Страницы: 6

SIMATIC MICRO-DRIVE

Бренд: Siemens Страницы: 39

1FL3041-0AC31-0BJ0

Бренд: Siemens Страницы: 60

6SL3210-5CC14-0UA0

Бренд: Siemens Страницы: 68

Бренд: Siemens Страницы: 100

Бренд: Siemens Страницы: 112

Бренд: Siemens Страницы: 124

SIMOREG DC Master 6RA7018-6DS22

Бренд: Siemens Страницы: 616

Бренд: TIS Страницы: 13

Бренд: Berger Lahr Страницы: 45

Бренд: Leadshine Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды