Eurotek EK-MFR/2 Скачать руководство пользователя страница 30

Страница: 30 / 66

EK-MFR/2

25/02/2016

Arch.5105 601-000147/MN Rev. Y

>>Volt in 0:

Allows to read a DC voltage (0÷12 VDC) eventually present on the
expansion connector.

>> Volt in 1:

Allows to read a DC voltage (0÷12 VDC) eventually present on the
expansion connector.

>> Volt out 0:

Allows to set a DC voltage (0÷12 VDC, 10 mA max) at the output of
the expansion connector.

>>Volt out 1:

Allows to set a DC voltage (0÷12 VDC, 10 mA max) at the output of
the expansion connector.

>>Board Temp:

Allows to read the EK-MFR/2 temperature.

>>12V rail:

Allows to monitory the DC voltage (12VDC) generated from the EK-
PWS/X board and supplied to all EK-MFR/2 slots.

Not valid for EK-PWS/A, EK-PWS/C and EK-PWS/D.

>>3.3V rail:

Allows to monitory the DC voltage (3.3VDC) generated from the EK-
PWS/X board, used by the processor and supplied to all EK-MFR/2
slots.

>>Dc rail in

Allows to monitory the eventual external DC voltage that is present on
the auxiliary connector of the EK-PWS/X board

Not valid for EK-PWS/A, EK-PWS/C and EK-PWS/D

>>Pws Upper Status

Indicates the voltage generated by one of the EK-PWS/A,EK-PWS/C,
EK-PWS/D modules located in the Upper position (before of the O-
ring diode).

Not valid for EK-PWS/x.

>>Pws Lower Status

Indicates the voltage generated by one of the EK-PWS/A,EK-PWS/C,
EK-PWS/D modules located in the Lower position (before of the O-
ring diode).

Not valid for EK-PWS/x.

>>Time to exit:

Allows to set the time when the display is on, afterward the display will
go in stand-by modality, in order to limit the consumption of the entire
machine. It is possible to set the time to exit parameter between
2,10,20, 30 or 360 minute.

>>SCI 2:

Allows to switch on and off the secondary serial interface.

>>Ext Power

Allows to read the value of the power of the external analog Eurotek
unit connected to the EK-MFR/2 by the expansion connector.

Содержание EK-MFR/2



































































Результаты поиска

Содержание EK-MFR/2

Отзывы:

Похожие инструкции для EK-MFR/2

Бренды по названию

Популярные бренды

Eurotek EK-MFR/2, Руководство пользователя

Результаты поиска

Содержание EK-MFR/2

Отзывы:

Похожие инструкции для EK-MFR/2

Бренды по названию

Популярные бренды