Eurotech DynaGate 10-12 Series Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 94

background image

DynaGATE 10-12 User manual Rev. 0-14

6 Norms and certifications

Cet appareil et son (ses) antenne(s) ne doivent pas être co-localisés ou utilisés en conjonction avec une
autre antenne ou un autre émetteur, sauf en conformité avec les procédures du produit multi-émetteur de la
FCC.

6.4.4

FCC Class B digital device notice

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired

operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This

product

generates,

uses

and

can

radiate

radio

frequency

energy

and,

if

not

installed

and

used

in

accordance

with

the

instructions,

may

cause

harmful

interference

to

radio

communications.

However,

there

is

no

guarantee

that

interference

will

not

occur

in

a

particular

installation.

If

this

product

does

cause

harmful

interference

to

radio

or

television

reception,

which

can

be

determined

by

turning

the

product

OFF

and

ON,

the

user

is

encouraged

to

try

to

correct

the

interference

by

one

or

more

of

the

following

measures:

l

Reorient or relocate the receiving antenna

l

Increase the separation between the product and the receiver

l

Connect the product into an outlet on a circuit different from that to which the receiver is connected

l

Consult the dealer or an experienced radio/TV technician for help

6.4.5

ISED Class B digital device notice

ICES-003 Class B Notice - Avis NMB-003, Classe B.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

6.4.6

Labeling information

The following information is stated on the product labels:

l

Contains FCC ID: RI7LE910NAV2

l

Contains FCC ID: UKMMRG1012

l

Contains IC ID: 5131A-LE910NAV2

l

Contains IC ID: 21442-MRG1012

l

CAN ICES-3 (B)/NMB-3(B)

25 / 94

«
...
23
24
25
26
27
...
»

Содержание DynaGate 10-12 Series































































































Отзывы:

Нет отзывов

Похожие инструкции для DynaGate 10-12 Series

Бренд: Eaton Страницы: 2

Бренд: JBM electronics Страницы: 20

Бренд: HMS Networks Страницы: 20

Бренд: ZyXEL Communications Страницы: 12

gesis LON R-56/0 (RC)

Бренд: Wieland Страницы: 47

Бренд: AudioCodes Страницы: 70

Бренд: RTA Страницы: 88

Бренд: Gree Страницы: 67

Бренд: Huawei Страницы: 28

WIP310 - iPhone Wireless VoIP Phone

Бренд: Cisco Страницы: 8

WIP310 - iPhone Wireless VoIP Phone

Бренд: Cisco Страницы: 276

Бренд: Alcatel-Lucent Страницы: 2

Xfinity DPC3939

Бренд: Comcast Страницы: 8

VoIP 2 ALL Series

Бренд: Discovery Telecom Страницы: 79

Бренд: Appareo Страницы: 9

Бренд: ADTRAN Страницы: 34

460BMSPBS-N70PB

Бренд: RTA Страницы: 79

LOHASmart CDM530AM

Бренд: Zalip Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды