background image

EUROSTER 11K CONTROLLER USER MANUAL

7

k) Relay activation delay

To increase lifetime of the controller output relays, outputs are prevented against activating/
deactivating   more  frequently   than   once   per   second.   However,  lights  signaling   state   of the

relays go on/off without any delay.

l) Output tests

The 

t1, t2, t3, tP, Ta

 installer parameters may be used to manually turn on/off the 

P1, P2,

P3

 pumps, throttle, and 

AUX

 outputs, respectively (to test them).

5. SETUP
a) User parameters

User parameters are system settings (temperature presets) that may be modified by the user.

Use the

  button to sequentially display preset temperature thresholds at which P1/P2/P3

pump, throttle, and  

AUX

 output are activated (press the button to display next preset). Use

the  

  and  

  buttons to modify the displayed value. Each modification must be confirmed

with the

button  or else the controller cancels it after 10 seconds. Use the  

  button to

cancel errors.
Only   user  parameters   used   in   the   given   system   layout   are   displayed,   those   not   used   are

hidden. User parameters include:

P1

Temperature at which the P1 pump is engaged. Range: 20÷85°C. Standard
value: 40°C.

P2

Temperature at which the P2 pump is engaged. Range: 20÷85°C. Standard
value: 40°C. Only for layouts 2 and 3.

P3

Temperature at which the P3 pump is engaged. Range: 20÷85°C. Standard
value: 45°C. Only for layouts 2 and 3.

THROTTLE

Preset fireplace temperature (throttle activation threshold). Range: (20 or

tb

)÷(70 or 

OH

–5°C). Standard value: 55°C.

AUX

Temperature   at   which   the  

AUX

  output   is   deactivated.   Range:   20÷85°C.

Standard value: 35°C.

b) Installer parameters (service mode settings)
ATTENTION  Installer   parameters  must   be  modified   knowledgeably  or  else  the  CH

system may start to work incorrectly. Therefore the parameters should be modified
exclusively by a qualified installer/serviceman.

Simultaneously press and hold the  

and

buttons to enter the service setup mode. Code

(symbol) of the first installer parameter is displayed. Use the  

  and  

  buttons to display

other parameters. Use the 

 button to display current value of the displayed parameter. Use

the  

  and  

  buttons to modify the displayed value. Each modification must be confirmed

with the

button or else the controller will cancel it after 1 minute. Use the  

  button to

cancel errors.

Installer   parameters   (system   settings   that   should   be   modified   only   by   a   qualified
installer/serviceman) include: 

H1

P1

  threshold hysteresis ( i.e. difference between temperature at which the P1

pump is engaged and temperature at which the pump is disengaged). Range:
1÷10°C. Standard value: 5°C.

H2

P2

 threshold hysteresis. Range: 1÷10°C. Standard value: 5°C.

H3

P3

 threshold hysteresis. Range: 1÷10°C. Standard value: 5°C.

HP

Throttle threshold hysteresis. Range: 1÷10°C. Standard value: 5°C.

HA

AUX

 output threshold hysteresis. Range: 1÷10°C. Standard value: 5°C.

tE

Put-out   temperature.   Range:   30÷(40   or  

tb

–10)°C.   Standard   value:   30°C.

Содержание 11K












Отзывы: