background image

25 

 

CHECK ARMATURE  

This should be checked at least 1 per month to check that there are visual signs of damage to the 
body or to the commutator. Some signs of wear will be seen on the commutator over a period of 
time this is normal as this is the part that comes in contact with the brushes but any signs of 
abnormal damage and the part should be replaced.

 

 

ADJUSTMENT OF SLIDE 

An essential requirement of the machine is that the slide can move in a smooth and controlled 
manner, free of lateral movement and vibration. 
 
This situation can be maintained by periodic adjustment of the slide and is accomplished in the 
following manner: 

1.

 

Place the machine in an upright position and, by means of the capstan, raise the slide to its 
highest position. Clean the aluminum rails and apply a small amount of light machine oil to 
the wear surfaces 

2.

 

Gently feed in setting screw with supplied Allen key 2.5until slight resistance is encountered. 
Follow your way down adjusting all setting nuts and screws 

3.

 

Operate the slide up and down a few times to test the movement and make any further 
necessary adjustments. Try to ensure that all the screws are exerting a uniform pressure on 
the slide from top to bottom. A perfectly adjusted slide will operate freely up and down 
without any sideways movement 

 
LUBRICATING THE FEED TRAVEL 

The feed travel should be lubricated periodically with grease to ensure smooth operation. 

-

 

Raise the motor unit to the highest position possible 

-

 

Lubricate the dove-tail guide way at both sides 

-

 

Lubricate the gear rack 

 
After repeated use, the gear rack may become loose. If necessary, adjust the 5 self-locking set 
screws at the left side. Tighten screws in series until the gear rack moves freely in the dove-tail guide 
but does not allow the motor to wobble. 
 

REPAIR, MODIFICATION AND INSPECTION 

Repair, modification and inspection of Euroboor Magnetic drilling machines must be done by 
EUROBOOR or an EUROBOOR authorized dealer. The spare parts list will be helpful if presented with 
the machine to the Euroboor dealer for service when requesting repair or other maintenance. 
 
Euroboor machines are constantly being improved and modified to incorporate the latest 
technological advancements. Accordingly, some parts (i.e. part numbers and/or design) may be 
changed without prior notice. Also, due to Euroboor's continuing program of research and 
development, the specifications of machines are subject to change without prior notice. 
 

WARNING: 

Since accessories, other than those offered by EUROBOOR, have not been tested 

with this product, use of such accessories with this tool could be hazardous. To reduce the risk 
of injury, only EUROBOOR recommended accessories should be used with this product. 

 
Consult your dealer for further information on the appropriate accessories. 
 

 

 

0800 536 774

 

[email protected]

www.globalweldingsupplies.com
13 Patiki Road Avondale, Auckland 1026

Содержание ECO.50S
































Отзывы: