EUCHNER 097945 Скачать руководство пользователя страница 21

Страница: 21 / 32

2110182-10-02/20 (Translation of the original operating instructions)

Operating Instructions

Non-Contact Safety Switch CES-A-C5H-EX

12. System status table

Operating mode

Actuator/door position

Safety outputs LA and LB

PLC

LED indicator

Output

State

Output

OUT (status signal)

ATE (gr

een)

OUT/ERROR

(yellow)

OUT/ERROR (r

ed)

Normal operation

closed

Normal operation, door closed

open

off

Normal operation, door open

Teach-in operation

(only unicode)

open

off

4 Hz

Initial setup after delivery, ready for first teach-in operation

closed

off

1 Hz

(60 s)

Teach-in operation

closed

off

Positive acknowledgment of completion of teach-in operation.

To activate the actuator code from the teach-in operation in the evaluation

unit, the operating voltage must then be switched off at the evaluation unit for

min. 3 seconds.

Status indication

(only unicode)

off

3 x +

Indication after 1st to 5th teach-in operation

off

2 x +

Indication of the remaining teach-in operations after the 6th teach-in operation

off

1 x +

Indication of the remaining teach-in operations after the 7th teach-in operation

off

Device cannot perform any further teach-in operation

Fault display

off

Internal component failure or

excessively high interference (EMC) or short circuit/external power at the LA/

LB safety output

Operating fault

(only unicode)

closed

off

1 x

Incorrect 9th teach-in operation (unicode only)

closed

off

2 x

Incorrect teach-in operation for an old actuator (unicode only)

closed

off

3 x

Negative acknowledgment for teach-in operation. Actuator was held in front

of the read head for less than 60 s

Key to symbols

0 Volt or not connected

24 Volt

0 Volt

LED not illuminated

LED illuminated

15 Hz (8 s)

LED flashes for 8 seconds at 15 Hz

3 x +

LED flashes three times and then illuminates continuously

3 x

LED flashes three times, and this is then repeated

Any state

After the cause has been remedied, faults can generally be reset by opening and closing the guard. If the fault is still dis-

played afterward, briefly interrupt the power supply. Contact the manufacturer if the fault could not be reset after restarting.

Important!

If you do not find the displayed device status in the system status table, this indicates an internal device

fault. In this case, you should contact the manufacturer.

Содержание 097945

































Результаты поиска

Содержание 097945

Отзывы:

EUCHNER 097945, Руководство по эксплуатации, Страница: 21 / 32

Результаты поиска

Содержание 097945

Отзывы: