ETS LEGEND 548 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 48

background image

Legend 548 Assembly and User Manual - 15

30068-02A

Lift springs under extreme tension.
Failure to properly install the shipping
pins could result in damage to the unit
and/or personal injury when removing
the canopy.

WARNING

Close the canopy and reinstall the shipping
pins to hold the lift system in place.
Remove the canopy cover and rear corner
covers.
The back of the canopy cover includes the
metal panel. Loosen the (8) 1/4-20 Phillips
screws securing the back covers just a few
turns. Do not remove these screws. The front
corners of the canopy cover are held by (1)
#10-32x1”

fl

at head screw in each corner.

Remove these screws. Carefully lift the cov-
er from the bed.
The rear corner covers are attached with (6)
#10x1/2” screws each. Simply loosen these
screws and the covers will slip off.

«
...
13
14
15
16
17
...
»

Содержание LEGEND 548

















































Отзывы:

Нет отзывов

Похожие инструкции для LEGEND 548

Бренд: 3Gen Страницы: 4

RABBIT PLAY TUNNEL END RINGS

Бренд: Omlet Страницы: 4

Бренд: TherAdapt Страницы: 2

Бренд: Sound Oasis Страницы: 10

Бренд: 4pets Страницы: 2

Achilles Brace System

Бренд: Caerus Страницы: 2

Бренд: sensiplast Страницы: 20

Бренд: Sensica Страницы: 44

Бренд: Fysic Страницы: 2

Бренд: Petsafe Страницы: 16

Бренд: Zoovilla Страницы: 7

Drinkwell D2KA-RE

Бренд: Petsafe Страницы: 32

Бренд: Tri-Tronics Страницы: 26

Бренд: Respireo Страницы: 64

Бренд: E-Collar Страницы: 34

Aeroneb GO 7010

Бренд: evo Medical Solutions Страницы: 2

Бренд: POLARIA Страницы: 2

Бренд: UFESA Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды