Etesia HYDRO 124D Скачать руководство пользователя страница 54

Страница: 54 / 79

- 54 -

If the module is not receiving information when there should be some, the causes
may be :

-  Malfunction of a switch/contactor
-  Cable disconnected between the switch/contactor and the module
-  Cable cut

If the module is permanently receiving information when there should not be any,
the causes may be :

- Malfunction of a switch/contactor
- Wear of the cables of a switch/contactor coming into contact with each

other.

THE ELECTRICAL HARNESSES

There are 5 harnesses, which group together all the cables of the Hydro 124D, thus allowing the
components to be connected to each other.
They are :

-  the main harness
-  the cover harness
-  the engine harness
-  the frame harness
-  the control valve harness

Moreover, each cable is a different colour according to its function :

-  Red : +12V
-  Orange : +12V intermediate
-  Blue : mass
-  Green : lights and road kit
-  White : contactors
-  Yellow : preheating and starting.

Содержание HYDRO 124D
















































































Результаты поиска

Содержание HYDRO 124D

Отзывы:

Похожие инструкции для HYDRO 124D

Бренды по названию

Популярные бренды

Etesia HYDRO 124D, Техническое учебное пособие

Результаты поиска

Содержание HYDRO 124D

Отзывы:

Похожие инструкции для HYDRO 124D

Бренды по названию

Популярные бренды