background image

19

8• MAINTENANCE

8•2•1 HYDROSTATIC UNIT OIL CHANGE 

OR REFILL

• Stop the engine for oil change or checks.
• Park the machine on a fl at and horizontal area.

LEVEL CHECK

• Check the oil level when the system is cold, by looking at the tank 

marked [UP] - [LOW] at the rear of the machine (see picture 8 page 10).

• First oil change : after 15 hours
• Next changes : every 100 hours or once a year
• Recommended oil : HV 46 (ref. : 29592 - 2 liters)
• Capacity : 0.5 l
• To drain the oil, unscrew and remove the drain plug (see a picture 9 

page 11). Let the oil fl ow and screw the drain plug again.

WARNING !

 Don’t let fl ow all the oil!

TO COMPLETE THE OIL LEVEL

• Fill the hydrostatic unit by the tank.
• Spill slowly the oil in order that no air is catched in the unit which 

could make the restart harder. 

• If in spite of this recommendation there is some air in the unit 

unscrew the venting plug (see b and c picture 10 page 11). As soon 
as some oil fl ows through it :
- Stop the venting plug.
- Refi ll until the level is slighty under the tank upper level mark.

WARNING ! 

Only use HV 46 quality oil to refi ll the 

hydrostatic tank (ref. : 29592 - 2 liters). We recommend to use 
an ETESIA fi lter unit fi tted with a 25 µm fi lter (ref. : 29977).

WARNING !

 Drive the machine (forward - reverse) and 

check the level. The level has to be between the [UP] and 
[LOW] marks. If necessary, to up.

• Dispose used oil in an approved collection point.

8•2•2 TRANSMISSION GEARBOX OIL 

CHANGE OR REFILL

• Stop the engine for oil change or checks.
• Place the machine on a fl at and horizontal area.
• Check the oil level when the system is cold. The level should reach 

the lower limit of the gauge and can be checked by unscrewing the 
gauge (see picture 11 page 11).

• First oil change : after 15 hours
• Subsequent changes : every 100 hours or once a year
• Recommended oil  : HD 220 (ref. : 29590 - 1 liter)
• Capacity : 1 l
• To change gearbox oil, unscrew the drain plug (see picture 12 page 

11). Let the oil fl ow and tight the drain plug.

• To refi ll, unscrew the oil level gauge (see picture 11 page 11) and 

fi ll with oil through this opening.

WARNING ! 

When the machine is on a fl at horizontal 

surface, the level shoud not exceed the lower limit of the gauge.

• Dispose used oil at an approved collection point.

8•3 MAINTENANCE OF THE 

TRANSMISSION AV98X 

(SEE HST OIL 

REPLACEMENT PAGE 14 AND 15)

8•4 MAINTENANCE OF THE 

BATTERY

8•4•1 MAINTENANCE OF THE 12 V BATTERY

• The 12 V battery is located under the front cover.
• This lead-acid battery requires very little maintenance.
• The level of the electrolyte should be checked every 50 hours, and 

should always lie between the upper [Max] and lower [Min] level 
markers. The level of the electrolyte in the cells can be checked 
without removing the battery, by opening the front cover.

• If the electrolyte level of a loaded battery is close to the [minimum] 

marker, add distilled water up to the level of the [maximum] 
marker. Never overfi ll the battery or add acid.

• Check that the battery terminals are not oxidized.
• If necessary, clean the terminals and coat with special battery 

grease.

WARNING!

 If, for any reason, it is necessary to 

disconnect the battery, always disconnect the negative 
terminal fi rst, followed by the positive terminal.

• In case of overfi lling of the battery when topping up, rinse the 

affected areas thoroughly to prevent corrosion.

8•4•2 CHARGING THE BATTERY

WARNING! 

Remove the battery from the ride-on brush 

cutter by disconnecting fi rst the negative terminal and then 
the positive terminal.

• Check the electrolyte level. If necessary, top up with distilled water.
• Wear the individual protection equipments that are necessary 

while making the maintenance of the battery (safety glasses and 
gloves…).

• Connect the battery to the charger.

- Charge voltage : 12 V
- Charging current : max. 3 A for AV98, 16 A for AV95
- Charge time : up to 12 hours, according to need.

Lead-acid batteries emit explosive gas mixtures during 
charging. Avoid naked fl ames and sparks and do not smoke. 
The battery should always be charged in a well-ventilated 
area. The battery contains sulphuric acid which is highly 
dangerous and liable to cause serious injury upon contact 
with the skin.

• Extreme care should therefore always be taken.

WARNING! 

In case of contact with the skin or eyes, 

rinse thoroughly with clear water. Seek medical attention 
immediately when necessary. Always keep the battery and 
acid out of the reach of children.

WARNING! 

Measures taken for the application of 

Directive 91/157/CEE relating to the marketing of batteries 
and accumulators containing certain hazardous materials 
and their elimination. 

ELIMINATION OF BATTERIES

Batteries contain hazardous materials and must under no 
circumstances be disposed off into the environment. They are the 
subject of specifi c rules governing their elimination.
You can return your used ETESIA batteries to your Approved Dealer 
free of charge, and he will take care of their elimination ; or you can 
give them to an organisation that deals specifi cally with waste or take 
them to a special battery collection point. 

WARNING!

 Batteries kept in a discharged state cannot 

subsequently be recharged and are not covered under the 
terms of the warranty.

Содержание AV95





























Отзывы: