Eternal GU145/508111145, Руководство по установке и эксплуатации

Страница: 22 / 56

22
Horizontal Termination
Side Wall (Direct Vent)
Side Wall (Concentric Vent)
Side Wall (Power Vent)
□
□
□
Below diagrams are examples of vertical terminations.
Once the vent terminal location has been determined, make a hole through the exterior wall to accommodate
the vent pipe. Vent pipe must only exit exterior wall horizontally.
Place the 1/2" metal mesh screen inside the terminal fitting and connect it as shown to the vent pipe on the
exterior of the building.
Seal any opening around the vent pipe or fittings with mortar or silicone caulk "as shown" above.
Complete the rest of the vent pipe installation to the water heater's vent connector fitting on the blower outlet.
If necessary support horizontal run as previously mentioned.
□
□
□
□
WARNING
! !
45 °
45 °
Exterior View
6"
Intake
Exhaust
Wall Thimble
2'*2' Sheet Metal
Shieldon Brick or
Masonry Walls
Vent Terminal with
1/2" Mesh Protective
Screen Inside
Intake pipe
Exhaust pipe
Outside of
Building Wall
Mortar or silicone caulk
6"
12"
Pipe Coupling
Wall Thimble
2'*2' Sheet Metal
Shieldon Brick or
Masonry Walls
Vent Terminal with
1/2" Mesh Protective
Screen Inside
Exhaust pipe
Mortar or silicone caulk
Pipe Coupling
6"
12"
Outside of
Building Wall
12" min. above Grade
or above snow level.
12" min. above Grade
or above snow level.
1" Min.
2" Max.
Combustion Air
12" min. above Grade
or above snow level.
Strap
Intake pipe
Exhaust pipe
1
1
2
" Min. Extension Through
Exterior Wall
Exterior Wall
Screw
Collar
Silicone
Sealer
Collar
Silicone
Sealer
Screw
Screw Screw
An open tee is optional and can be
used as termination to alleviate back
pressure in the venting system in areas
experiencing abnormally high winds
Vent cap must be
positioned downward
Screen
1
1
2
" Min. Extension Through
Exterior Wall
Exterior Wall
Screw
Collar
Silicone
Sealant
Collar
Silicone
Sealant
Screw
Screw Screw
An open tee is optional and can be
used as a termination to alleviate back
pressure in the venting system in areas
experiencing abnormally high winds.
Vent cap must be
positioned downward
Screen
For optimal results the open tee
should be positioned vertically.
Wall Thimble
2'*2' Sheet Metal
Shieldon Brick or
Masonry Walls
Vent Terminal with
1/2" Mesh Protective
Screen Inside
Intake pipe
Exhaust pipe
Outside of
Building Wall
Mortar or silicone caulk
Pipe Coupling
Wall Thimble
2'*2' Sheet Metal
Shieldon Brick or
Masonry Walls
Vent Terminal with
1/2" Mesh Protective
Screen Inside
Exhaust pipe
Mortar or silicone caulk
Pipe Coupling
6"
12"
Outside of
Building Wall
12" min. above Grade
or above snow level.
12" min. above Grade
or above snow level.
6"
12"
Wall Thimble
2'*2' Sheet Metal
Shieldon Brick or
Masonry Walls
Vent Terminal with
1/2" Mesh Protective
Screen Inside
Intake pipe
Exhaust pipe
Outside of
Building Wall
Mortar or silicone caulk
Pipe Coupling
Wall Thimble
2'*2' Sheet Metal
Shieldon Brick or
Masonry Walls
Vent Terminal with
1/2" Mesh Protective
Screen Inside
Exhaust pipe
Mortar or silicone caulk
Pipe Coupling
6"
12"
Outside of
Building Wall
12" min. above Grade
or above snow level.
12" min. above Grade
or above snow level.
6"
12"
45 °
45 °
Exterior View
6"
Intake
Exhaust