background image

2

CEM3 Sensor Rack Retrofit Manual

Help from ETC Technical Services

If you are having difficulties, and your problem is not addressed by this document, try the ETC support 
website at 

support.etcconnect.com

 or the main ETC website at 

etcconnect.com

. If none of these 

resources are sufficient, contact ETC Technical Services directly at one of the offices identified below. 
Emergency service is available from all ETC offices outside of normal business hours.

When calling for help, take these steps first:

• Prepare a detailed description of the problem
• Go near the equipment for troubleshooting
• Find your notification number if you have called in previously

Americas

United Kingdom

ETC, Inc.

ETC Ltd - UK

Technical Services Department

Technical Services Department

3031 Pleasant View Road

26-28 Victoria Industrial Estate

Middleton, WI 53562

Victoria Road,

800-775-4382 (USA, toll-free)

London W3 6UU England

+1-608 831-4116

+44 (0)20 8896 1000

[email protected]

[email protected]

Asia

Germany

ETC Asia

ETC GmbH

Technical Services Department

Technical Services Department

Room 1801, 18/F

Ohmstrasse 3

Tower 1, Phase 1 Enterprise Square

83607 Holzkirchen, Germany

9 Sheung Yuet Road

+49 (80 24) 47 00-0

Kowloon Bay, Kowloon, Hong Kong

[email protected]

+852 2799 1220

[email protected]

France

ETC France

Zone Urbaparc -

Bâtiment E

6 Boulevard de la Libération

Saint-Denis, 93200

+33 1 4243 3535

techservltd@etcconnect.com

Содержание Sensor3





















Отзывы: