ESI RF BRIDGE Скачать руководство пользователя страница 5

Страница: 5 / 19

ESI RF BRIDGE

User Guide

version 1.0.4.0

www.elec-solutions.com

Page 5 of 19

Configuration Menu:

d. OPTIONAL: change the Baud Rate.

Press the “1” key

se an arrow key to select the “Baud rate” entry in the Configuration Menu,

then press the Enter key.

2. In the Baud rate sub-menu, p

ress the “1” “2” or “3” key

use an arrow key to select a different

Baud rate, then press the Enter key.

Baud rate sub-menu:

3. Change the Baud rate in the terminal emulator program on the PC to match the ESI RF Bridge.
4. Power-cycle the ESI RF Bridge.

NOTE

: the Baud rate does not change on the ESI RF Bridge until power is turned off, then turned

back on.

To return to the Configuration Menu from the Baud rate sub-menu:



ress the “0” key

use an arrow key to

select the “Back” entry, then press the Enter key.

e. OPTIONAL: change other settings, by selecting the item in the Configuration Menu, and making a

selection in the sub-menu that appears.

Exit the Configuration Menu:

Press the

“0” key

use an arrow key to

select the “Exit Configuration”

entry in the Configuration Menu, then press the Enter key.

D. STEPS

— Create an ESI RF Network

IMPORTANT

: A SUITE remote is OPTIONAL.



RF MOTOR:

Each SUITE Arc remote (Setup Mode) can administer up to 16 ESI RF motors

—

Toggle Motor Direction, Set/Adjust/Clear Limits and set the PRESET. The SUITE Step remote
can administer up to 4 ESI RF motors.



RF MOTOR:

If no SUITE remote is in the network, Toggle Motor Direction and

Set/Adjust/Clear Limits can be performed using the head buttons on an ESI RF motor.



RQ MOTOR / STANDARD MOTOR:

A SUITE remote can only set the PRESET on RQ motors

or RQ motor controls (standard motor) that are connected to the ESI RF RQ Transceiver.



USER MODE:

A SUITE remote in User Mode can control all motors in a network.

Содержание RF BRIDGE




















Результаты поиска

Содержание RF BRIDGE

Отзывы:

Бренды по названию

Популярные бренды

ESI RF BRIDGE, Руководство пользователя

Результаты поиска

Содержание RF BRIDGE

Отзывы:

Бренды по названию

Популярные бренды