ESD CPCI-405 Скачать руководство пользователя страница 7

CPCI-405  

   Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5

Page 7 of  57

5.2 CPCI-405-A PCI-Adapter with 6 U Front Panel (I.2306.47) . . . . . . . . . . . . . . . . . . . . . . . . 39

5.2.1 Front Panel view of the CPCI-405-A PCI-Adapter with 6 U Front Panel . . . . . . . . 40

5.3 Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

5.3.1 RS-232 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
5.3.2 RS-422 interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
5.3.3 RS-485 interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
5.3.4 Solder Bridges for the Configuration of the Serial Interface SER1 . . . . . . . . . . . . . 43

5.4 Connector Assignments of the Special Designs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

5.4.1 CAN-Interface CAN 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
5.4.2 SER1: Assignment of the RJ12 Socket P100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

6. Correct Wiring of Electrically Isolated CAN Networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

6.1 Standards concerning CAN Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
6.2 Heavy Industrial Environment (Double Twisted Pair Cable) . . . . . . . . . . . . . . . . . . . . . . . . 47

6.2.1 General Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
6.2.2 Device Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
6.2.3 Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

6.3 Light Industrial Environment (Single Twisted Pair Cable) . . . . . . . . . . . . . . . . . . . . . . . . . . 49

6.3.1 General Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
6.3.2 Cabling

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

6.3.3 Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

6.4 Electrical Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
6.5 Bus Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
6.6 Examples for CAN Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

6.6.1 Cable for Light Industrial Environment Applications (Two-Wire) . . . . . . . . . . . . . . 52
6.6.2 Cable for Heavy Industrial Environment Applications (Four-Wire) . . . . . . . . . . . . . 52

7. CAN-Bus Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

7.1 Termination  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
7.2 Electrical Grounding  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
7.3 Short Circuit in CAN Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
7.4 CAN_H/CAN_L Voltage  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
7.5 CAN Transceiver Resistance Test  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
7.6 Support by esd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

8. EU Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

9. Order Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Содержание CPCI-405


























































Отзывы: