ESD CPCI-405 Скачать руководство пользователя страница 57

Страница: 57 / 57

Order Information

CPCI-405

Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5

Page 57 of 57

9. Order Information

Type

Features

Order No.

CPCI-405

AMCC PowerPC405GPr, 266 MHz, 64 MB SDRAM,
4 MB Flash, CPCI-host

I.2306.04

CPCI-405-64

as I.2306.04, but AMCC PowerPC405GPr with 400 MHz

I.2306.05

CPCI-405-A

as I.2306.04, but CPCI-target adapter

I.2306.07

as I.2306.07, but with 4 HP / 6 U front panel

I.2306.47

CPCI-405-A-64

as I.2306.05, but CPCI-target adapter

I.2306.08

CPCI-405-2 Host 400
MHz/128MB/RTC

AMCC PowerPC 405GPr Host, 400MHz,: 128MB
SDRAM, Real Time Clock, CompactPCI 8TE/3U board,
Front panel: 2x CAN, 2x Serial RS-232, 1x Ethernet

I.2306.12

CPCI-405-2

as I.2306.04, but 2x CAN ISO11898 and 2x Serial RS-232,
8 HP / 3 U front panel

I.2306.49

CPCI-405-VxW

VxWorks BSP

I.2306.30

CPCI-405-Linux

Linux BSP/Adaption

I.2306.32

CPCI-405-QNX

QNX6 BSP

I.2306.34

Table 3: Order information

PDF Manuals
Manuals are available in English and usually in German as well. For availability of English manuals
see the following table.
Please download the manuals as PDF documents from our esd website

www.esd.eu

for free.

Manuals

Order No.

CPCI-405-ME

Manual in English

C.3010.21

Table 4: Available manuals

Printed Manuals
If you need a printout of the manual additionally, please contact our sales team:

[email protected]

for a

quotation. Printed manuals may be ordered for a fee.

Содержание CPCI-405


























































Результаты поиска

Содержание CPCI-405

Отзывы:

ESD CPCI-405, Руководство по оборудованию, Страница: 57 / 57

Результаты поиска

Содержание CPCI-405

Отзывы: