background image

41

LIMITED 5 YEAR WARRANTY 

 

This consumer warranty extends to the original consumer purchase of any Escalade

® 

Sports Product 

(hereinafter referred to as the “Product”).  

WARRANTY COVERAGE: 

Escalade 

Sports warrants to the original Consumer Purchaser that any Product of 

its manufacture is free from defects in material and workmanship. THIS WARRANTY IS VOID IF THE 
PRODUCT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER 
SERVICE, FAILURE TO FOLLOW INSTRUCTIONS PROVIDED WITH THE PRODUCT OR OTHER CAUSES 
NOT ARISING OUT OF DEFECTS IN MATERIAL OR WORKMANSHIP.  

Subject to 

proper assembly, installation 

and normal Residential use, Escalade 

Sports warrants, subject to the limitations 

below, to the original retail purchaser all structural components (not accessories) of the Silverback

® 

System to be free of 

defects in material and workmanship for a period of Five (5) years from the original 

purchase date

.  

Merchandise must be shipped prepaid with a copy of proof of purchase to Escalade 

Sports factory for examination to 

determine if the basketball system needs to be repaired or replaced. Any labor costs, travel expenses and any other 
changes involved in the removal, installation or replacement of the defective/repaired parts from/to your Silverback 
System will be the purchaser’s responsibility. Shipping charges for replaced or warranted merchandise sent back to the 
customer from Escalade Sports factory must be prepaid by the customer in advance. If not, the replacement shipment 
will be sent out collect.  

Escalade

 

Sports reserves the right to examine photographs or physical evidence of merchandise claimed to be 

defective, and to recover said merchandise, prior to authorization of warranty claims. A “Returned Goods 
Authorization” number may be required, please call for details prior to the return of any photographs or 
merchandise.  

This limited 5 year warranty is expressly in lieu of all warranties, expressed or implied, including warranties of merchantability 
or fitness for use. Escalade

® 

Sports does not assume or authorize any person or representative to assume for us, any 

other liability in connection with the sale of our products.  

The remedy of repair or replacement stated above is Escalade 

Sports exclusive remedy. Escalade

 

Sports will not be 

liable for any other damages or expenses which may incur, including but not limited to incidental or consequential 
damages. Escalade Sports assumes no other obligations or liability on the part of the purchaser, and Escalade 
Sports neither assumes nor authorizes any other person to assume for it any other liability in connection with the 
goods sold.  

This warranty shall not apply in any manner to parts or accessories not manufactured by Escalade 

Sports.  

NOT COVERED BY THIS WARRANTY  

• 

Merchandise not intended to be in places of public assembly, such as, but not limited to, schools,  
parks, public or private recreational facilities. 

• 

Any merchandise subjected to Non-residential abuse, negligence, improper installation, vandalism,  

 

acts of God, alteration of product, or any other events beyond the control of Escalade 

 

Sports. 

• 

Paint or rusted parts. If rust should appear, remove loose paint, sand lightly, primer and paint with  
exterior flat matte finish enamel paint. 

• 

Hoop net will be warranted for a period of 180 days - under normal use and proper care. 

• 

HANGING ON RIM WILL VOID THE WARRANTY: Rims are not warranted for any defects other than  
workmanship. Torn back plates, damaged springs, bent rings, damaged eyebolts, and torn or distorted  
rim supports result from hanging on the rim and are not warranted. 

• 

Shipping charges both ways. Note: Any merchandise shipped to Escalade 

 

Sports collect will be  

refused.  

• 

Dealer service charges, labor charges and travel expenses associated with replacement of repair of  
warranty item. 

  

WARRANTY DISCLAIMERS: 

ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING BUT NOT 

LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, 
ARE LIMITED IN DURATION. ESCALADE 

SPORTS SHALL NOT BE LIABLE FOR LOSS OF USE OF THE 

PRODUCT OR OTHER CONSEQUENTIAL OR INCIDENTAL COSTS. EXPENSES OR DAMAGES INCURRED BY 
THE CONSUMER OF ANY OTHER USE.  

Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental damages, so the above 
limitations or exclusions may not apply to you. LEGAL REMEDIES: This warranty gives you specific legal rights, and you may 
also have other rights which may vary from state to state.  

WARRANTY GUIDELINES IS REQUIRED FOR ALL WARRANTY CLAIMS 

 

1.  Proof of Purchase (original retail purchaser) is required for all warranty claims.  
2.  Call or write Escalade

 

Sports to receive a Return Authorization # and determine specific needs. 

 Phone: 1-888-USA-GOAL / Warranty Dept. Or Write Escalade

 

Sports at: Escalade

 

Sports - P.O. Box 889, 

Evansville, IN 47706 - Attn: Warranty Dept. Or E-mail us at: [email protected]  

 

Содержание B8405F










































Отзывы: