manualshive.com logo in svg

Eriez E-Z TEC IV, Инструкции по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Eriez E-Z TEC IV Скачать руководство пользователя страница 42

®

42

Configuring Analog Metal Detector

Please read the Introduction to the Control
Panels and Displays section prior to attempting
to adjust the metal detector.

All installation procedures must be complete
before configuring the metal detector.

ANALOG ADJUSTMENT
PROCEDURE

1.

Open the switch to the auxiliary equipment

(reject device, horn, etc.) where fitted.

2.

Switch the power to the metal detector on.

The metal detector will be ready for op-
eration in approximately 30 seconds.

3.

Each unit is supplied with an “Individual

Unit Specifications” test sheet. Consult this
sheet and set the phase control to the
“Product Phase Out” setting. If no listing
is given, set the phase control to the “Vi-
bration Phase Out” setting.

4.

Pass one of the test wands through the

center of the search head opening at the
expected speed that the product will pass.
The light bar should indicate that metal has
passed through the opening.

Set the SENSITIVITY so the DETECT in-

dicator turns on every time the test wand
is passed through the center of the open-
ing. Do not set the Sensitivity higher than
necessary as this can cause false detec-
tions due to the product and/or vibration.

5.

To fully check the operation of the metal

detector, pass an uncontaminated sample
of the product, which has the same size
and mass of that typically encountered,
through the search aperture at its normal
speed of travel. If detection occurs, refer
to the “Phasing out the Product Effect”
section of this manual.

6.

Having adjusted the detector, the auxiliary

equipment can be switched on and the
metal detector system operated.

PHASING OUT THE PRODUCT
EFFECT ANALOG UNITS

Some products are conductive or magnetic in
nature and can produce a signal when passing
through the metal detector.

This signal is known as “PRODUCT EFFECT” and
can be “PHASED OUT” by using the front panel
controls as follows:

1.

Obtain a sample of the product which is char-

acteristic of that which will normally pass
through the metal detector. Without a product
or metal signal present, the MONITOR should
display two green LED’s. As a product passes
through the aperture, the red LED’s on either
side of the two green LED’s light. As the prod-
uct enters the aperture, note that one side of
the red LED’s lights first; this is the INITIAL
DEFLECTION of the Monitor. As the product
continues through the aperture, the initially lit
LED’s go out and the LED’s on the other side
of the Monitor light. As the product exits the
aperture, the red LED’s go out leaving only the
two green LED’s lit.

2.

Adjust the Phase switch to 00.0.

3.

Pass the product through the aperture of the

metal detector in a manner consistent with nor-
mal production process techniques (e.g. on the
conveyor, in a chute, etc.). If it is necessary to
pass the product through the aperture manu-
ally, the hand must not come close to the ap-
erture because it will affect the metal detector.
In this case place the product on a piece of
wood or plastic and push it through the aper-
ture. The sample used to phase out the prod-
uct effect must have the same properties (e.g.
temperature, size, orientation, moisture con-
tent, component composition, etc.) as that
which will be scanned during production.

NOTE:  Throughout the following adjust-

ment procedure, always be sure to pass
the product through the aperture in the
same direction.

Содержание E-Z TEC IV





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды