manualshive.com logo in svg

Eriez E-Z TEC IV, Инструкции по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Eriez E-Z TEC IV Скачать руководство пользователя страница 16

®

16

E-Z Tec IV and V metal detectors have been
manufactured to very stringent quality control
standards to ensure that they will provide years
of trouble-free service. To achieve this trouble-
free service, the installer must follow the
installation procedures outlined in this manual.
The details of the procedures are important, and
must be followed precisely for proper metal
detector operation.

A metal detector is by nature extremely sensitive
to very small changes in its electrical and physical
environment. Installed incorrectly, it will be very
likely to display unstable operation. It will appear

to be extremely sensitive to vibration and/or will
false trip (generate a false reject signal) when
the conveyor starts and stops. These and other
troubles will be prevented by proper installation
techniques.

The following installation procedures have been
collected over years of experience. Please make
use of them! Problems caused by improper
installation techniques are not covered by
warranty! A little time invested in the installation
process will pay for itself many times over by
providing a smooth trouble-free startup and
continued reliable service.

Installation Caution!!

Mechanical Installation

INTRODUCTION

The metal detector contains from one to three
components which must be physically mounted to
a conveyor or suitable stand: 1) the sensing head,
2) the control (including the MPC in MPC versions)
if it is not part of the sensing head, and 3) the power
supply which may be integral with the sensinghead
and/or this control. See Figure 6.

The sensing head includes the sensing aperture
and related electronics. The control is either
attached to the sensing head or remote from it. If
the control is remote from the sensing head, its
enclosure must be mounted to a convenient
surface (free of vibration) that is easy to access
so that the metal detector can be adjusted. The
control enclosure is fitted with plastic mounting
feet that must be used to mount it.

The power supply contains all the electrical
connections to the metal detector. It is located
within a NEMA-4X enclosure (see Figure 7). This
enclosure is also fitted with plastic mounting feet
that must be used  to mount it.

HANDLING

The metal detector must be handled with care
during installation. Follow the specific handling
guidelines attached to the detector or included in
the shipping materials. For convenience, generic
handling guidelines are included in this manual
immediately inside the front cover.

LOCATION OF SENSING HEAD

The location of the metal detector sensing head
is extremely important. The process of selecting
a location must include consideration of the needs
of the metal detector, the surrounding processing
equipment, and the operator. Product flow
including velocity and rejection of contaminants
is a major concern. Be certain to read and
understand all installation guidelines before the
final location is selected.

Содержание E-Z TEC IV





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды