background image

Figure 11 - External Alarm Relay

EXTERNAL SPEAKER KIT - OPTION PMZM1K

The external speaker kit includes a speaker (option PMLSIF) and an external

speaker cable (option PMCC9M). External speaker cable (option PMCD1W) is
available for use with this kit to place the external speaker up to 16 feet further
away from the radio. Installation of this kit requires the option cable kit - option
PMD7Z.

1.

Mount the speaker so it is directed to the operator but does not cause interfer-
ence with his vision. It also should not present a hazard in the event of an
accident. The speaker may be mounted on the lower edge of the instrument
panel, the fire wall, or above the windshield in some trucks. Use the mounting
bracket as a template for locating the mounting holes, and mount the speaker
as shown in Figure 12.

2.

Install the option cable PMCD7Z if not already present.

3.

Pins are supplied on the ends of the external speaker cable option PMCC9M.
Push these pins into sockets 2 and 9 of the connector housing supplied with
the option cable. Refer to Figure 9 and Table 2.

4.

Plug the connector housing into P2 of the option cable.

5.

Connect the plug end of the external speaker cable to the speaker. If installing
the external speaker cable option PMCD1W connect it between the speaker
and the plug end of the external speaker cable option PMCC9M.

22

Interference with Vehicular Electronics - Electronic fuel injection sys-
tems, electronic anti-skid braking systems, electronic cruise control sys-
tems, etc., are typical of the types of electronic devices which may be prone
to malfunction due to the lack of protection from radio frequency energy
present when transmitting. If the vehicle contains such equipment, consult
the dealer for the make of vehicle and enlist his aid in determining if such
electronic circuits will perform normally when the radio is transmitting.

WARNING

It is suggested that the radio be installed by one of the many Authorized Service

Centers located throughout the United States. These experienced service centers
can provide a proper radio installation and make any final adjustments that may be
needed.

Figure 1 -  Dual Format MDR Mobile Radio Components and Mounting

Hardware

7

Содержание DUAL FORMAT MDR





























Отзывы: