ErgoPack Air 713-580 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 63

ErgoPack Air 713-580 Скачать руководство пользователя страница 12

-12-

Attention: Laser beam!

Direct eye contact with the laser beam or reflecting
radiation may result in permanent eye injuries. Never
look direct into the laser.
Laser Klasse 2
DIN EN 60825-1:2015-07

Warning:
Strap tensioning or strapping, danger of jamming and crushing.

Do not place hands or other body parts between the strap and
the packaged goods during the strapping process. Ensure that
there are no other persons in the hazardous zone.

For an emergency stop in case of danger (trapped person):

To release tension (before welding), open the rocker lever.
After welding, cut the strap with a suitable tool (strap cutter)

Attention: Risk of squeezing!

There is a risk of squeezing in the entire surroundings of
the ChainLance, but especially between the metal chain
pieces of the supporting ChainLance; also in the area of
the reversing sledge, the tensioning wheel, the guiding
wheel and between the lifting unit and the chassis.

Attention : Risk of tripping!

If the system will be parked, the supporting ChainLance
has to be fully retracted. The supporting ChainLance
must not protrude from the system.

Furthermore, it must be assured that any potential strap
waste or strap pieces are removed from the floor
immediately.

«
...
10
11
12
13
14
...
»

Содержание Air 713-580
































































Отзывы:

Нет отзывов