Ercogener 4408100066 Скачать руководство пользователя страница 44

Страница: 44 / 51

EG_GenPro425e_1103_UG_001_UK.docx

Page 44 / 51

Descriptions and non-contractual illustrations in this document are given as an indication only.

ercogener reserves the right to make any modifications.

Dct_427_02

5.5 Verification of PIN code

The PIN code is necessary to make a call or to accept a response coming from the cellular network. This

code is held in the SIM card and can be modified by the user.

To check that the PIN code has been entered, use a communication software like HyperTerminal, and enter

the command

AT+CPIN?

The table below shows the main responses given by the modem:

Table 37 : Verification of PIN code

Command

Response

Interpretation

AT+CPIN?

ERROR

The SIM card is absent or not
recognized

+CPIN : READY

The PIN code is correct

+CPIN : SIM PIN

The PIN code is wrong or not entered
yet

+CPIN : SIM PUK

The PUK code is required

Enter the PIN code with the AT command

AT+CPIN="xxxx"

The user has only 3 attempts to enter the PIN code. After the third attempt, only a second code (code PUK)

supplied by the operator, will allow you to choose a new PIN code.

5.6 Checking the quality of the cellular reception signal

The modem will be able to make a call only if the received signal is powerful enough.

To verify the reception level, the SIM card must be inserted and the PIN code entered.

The command

AT+CESQ

allows to know the reception level of the signal sent by the closest cellular Base

Transceiver Station (BTS).

This level is given when modem is attached to the network. The modem is attached to the network when

answer to AT+COPS? command is provided.

To check the level of the received cellular signal, do the following operations:

Use a communication software like Hyperterminal.

Enter the commands

AT+COPS?

The response

+COPS : <mode>,<format>,”Operator”,Act>

As long as response is

+COPS : 0

send again command

AT+COPS?

When the modem is attached, the answer looks like

+COPS : 0,0,"FirstOne",7

Act = 0, 1 or 3, the modem is attached to 2G network

Act = 2, 4, 5 or 6, the modem is attached to 3G network

Act= 7, the modem is attached to 4G network

Enter command

AT+CESQ?

The answer is

+CESQ : <rxlev>,<ber>,<rscp>,<ecn0>,<rsrq>,<rsrp>

Содержание 4408100066




















































Результаты поиска

Содержание 4408100066

Отзывы:

Ercogener 4408100066, Руководство пользователя, Страница: 44 / 51

Результаты поиска

Содержание 4408100066

Отзывы: