manualshive.com logo in svg

Ercogener 4408100066, Руководство пользователя, Страница: 20 / 51

Поделиться
Скачать
Ercogener 4408100066 Скачать руководство пользователя страница 20

 

EG_GenPro425e_1103_UG_001_UK.docx

 

Page 20 / 51 

 

Descriptions and non-contractual illustrations in this document are given as an indication only. 

ercogener reserves the right to make any modifications. 

Dct_427_02

 

3.4.3 

Internal battery option (S0531) 

This  battery  allows  to  maintain  the  operation  of  the 

GenPro 425e

  in  case  of  absence  of  its  external  power 

supply. 

The  internal  charging  circuit  allows  to  keep  permanently  the  charge  of  the  battery  from  the  external  power 

supply.  

When the battery is completely discharged, 4 h are necessary to obtain a new complete charge. It is normal 

if the box is becoming a little bit hot in this case. 

The  autonomy  of  the  battery  mainly  depends  on  the  mode  of  use  of  the 

GenPro  425e

  (attachment  in 

LTE/3G/GPRS/GSM, Inputs/Outputs, RS232 connected...). 

 

 

In  the  case  where  the  software  management  of  the  battery  guarantees  that  the  voltage  V

BAT

 

does  not  goes  below  3,5  V.  The  autonomy  depends  on  data  volume,  transmit  power  and 
communication  type  4G,  3G,  2G.  With  a  new  battery  completely  charged,  the  autonomy  is 
around: 

  Between  1h  and  4h  continuous  data  transfer,  maximum  transmit  power,  according  type  of 

communication. 

  Up to 11h attached to the network without data transfer. 

 

 

When the battery is charged, it is not possible to do an ON/OFF of the device. Only putting the 
Reset input (pin 10 of the 16-pin Micro-FIT connector) to the Ground or sending the command 
AT+EGMRST=0 allows a reset of the modem. 

 

 

Below  0°C  and  above  45  °C  inside  the  device,  the  protection  of  the  battery  management 
triggers. The battery will not be charged. 

 

 

If  the  battery  is  present,  prepare  the  modem  for  storage  or  transport  conditions,  in  order  to 
limit high discharges of the battery. For this, see § 5.2 

Turning the device OFF

 

 

Table 9 : Characteristics of the polymer lithium battery

 

 

 

The  battery  cannot  be  replaced  or  modified  by  the  user;  the  device  must  never  be  opened. 
For any intervention on the battery: the device must be returned to the factory. 
Do not throw the modem and the battery on fire. 

Voltage min (cut off) / max. 

3.0V / 4.2V 

Type 

Lithium Polymer (Li Polymer) 

Capacity  

950 mA/h typique 

Exp. life time at 0.5C/0.5C 

>300 cycles >80%  of initial capacity at 20°C 

Temperature range 

Charge : 0°C to +45°C 

Discharge : -20°C to +60°C 

Max. charging current / discharging 
current 
 

950mA 

Содержание 4408100066




















































Отзывы:

Нет отзывов